Kuryakyn 3201 Lighted Trunk Moldings Instruction Manual

LIGHTED TRUNK MOLDINGS
3201

INSTALLATION

PARTS INCLUDED

1 Lighted Molding — Right
1 Lighted Molding — Left
1 Lighted Molding — Center
1 Wiring Kit Containing
1 6 Connector Wiring Adapter
1 26” Extension Wire
10 4” Black Nylon Cable Ties
1 Installation Instructions

Please read and understand entire instructions before starting installation.

THANK YOU FOR CHOOSING KϋRYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES REGARDINTHE USE  AND CARE OF THIS PRODUCT.

WARNING! THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.

ATTENTION! This indication alerts you to the fact that ignoring the contents described herein may negatively affect product performance and functionality.

CAUTION! This indication alerts you to the fact that ignoring the contents described herein can result in potential injury or material damage.

TOOLS SUGGESTED

Phillips Head Screwdriver, Set of Metric Hex Wrenches, Diagonal Cutters

STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.

STEP 1

Read and understand all steps in the instructions before starting the installation. Park the motorcycle on a hard, level surface and turn off the ignition.

CAUTION!
Avoid potential electrical shock! Disconnect the battery before starting this procedure.

STEP 2

Remove the stock trunk moldings. The side moldings must be removed first.
Each side molding is secured by two Phillips head screws accessible from the inside of the trunk. PIC 1 Shows the approximate placement of the screw holes in the trunk. (The moldings have already been removed in this picture.) After removing the screws, gently  pull out on the molding to release the tabs.
There is a tab at the rear of each side molding that interlocks into the center molding securing the corners.
Remove the center section by removing the Phillips screw at each end and unsnapping the molding from the trunk.

STEP 3

See PIC.2. Remove the rear center panel, between the saddlebags. There is a button head hex bolt in each corner of the panel, and one located behind the license plate (on older models).

NOTE:If you have an existing Kuryakyn LED accessory light installed on the rear of the motorcycle and do not want to install a second harness adapter, you may use Kuryakyn Part Number 7302, Multi Plug and Play harness with the existing harness adapter to  gain the plug7ins for the Lighted Trunk Moldings.

STEP 5

Locate the following components: trunk light plugs and cover (see PIC.3) and the wired connector (see PIC.4).

ATTENTION! Küryakyn recommends the use of dielectric grease on electrical connections.

STEP 6

Unplug either the blue or red plugs and insert shown in PIC.5. Plug the 26” power extension the 6 connector wiring adapter wire into either of the accessory a light plugs. PIC 5

STEP 7

Route the power extension wire up, and inside the trunk bottom panel so the remaining plug and short length of wire hangs out of the rear center of the tr panel. Use the included wire ties to secure this power wire out of harms way.
FIG.1 (line drawing) shows one possible wire routing. unk

ATTENTION! Secure all wiring away from any moving parts, pinch points or extreme heat. Küryakyn WILL NOT issue a warranty on any electrical component that fails due to pinched, crimped, broken, abraded, melted or frayed wires.

STEP 8

Replace the rear center panel, and bottom trunk panel.

ATTENTION! Küryakyn recommends the use of dielectric grease on electricaconnections.

STEP 9

Plug the power extension wire into the plug in the center of the rear molding.
Route the two end leads out the opening in each interlocking tab. See PIC.6.

STEP 10

Snap and screw the center molding into place.

STEP 11

Plug each side molding plug into the corresponding plugs in the center molding.
Install each side molding in the same manner as the stock ones were removed.
Secure with the two stock Phillips screws per side.

ATTENTION! It is the installer’s responsibility to ensure that all of the fasteners (including pre7assembled) are tightened before operation of the motorcycle. Küryakyn will not issue a warranty on components lost due to improper installation. Periodic  maintenance may be required.

STEP 12

Reconnect the battery and test all lights.

WARNING! ENSURE PROPER LIGHT OPERATION BEFORE RIDING THE MOTORCYCLE. VISIBILITY IS A MAJOR CONCERN FOR MOTORCYCLISTS. A LIGHT MALFUNCTION COULD RESULT IN DEATH OR SERIOUS INJURY

Ride On!

CUSTOMER SERVICE
877.370.3604 (toll free)

INSTALLATION QUESTIONS
techsupport@kuryakyn.com
or call 715.247.2983

LIMITED WARRANTY

Küryakyn warrants that any Küryakyn products sold hereunder, shall be free of defects in materials and workmanship for a period of one (1) year from the date of purchase by the consumer excepting the following provisions:

• Küryakyn shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the product(s).

• The product must be properly installed, maintained and operated under normal conditions.

• Küryakyn makes no warranty, expressed or implied, with respect to any gold plated products.

• Küryakyn shall not be liable for any consequential and incidental damages, including labor and paint, resulting from failure of a Küryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condition, or for any breech of contract or  duty between Küryakyn and a customer.

• Küryakyn products are often intended for use in specific applications. Küryakyn makes no warranty if a Küryakyn product is used in applications other than intended.

• Küryakyn electrical products are warranted for one (1) year from the date of purchase by the consumer. L.E.D.’S contained in components of Küryakyn products will be warranted for defects in materials and workmanship for 3 years from the date of  purchase where as all other components shall be warranted for one(1) year.
  This includes, but is not limited to; control modules, wiring, chrome & other components.

• Küryakyn makes no warranty of any kind in regard to other manufacturer¹s products distributed by Küryakyn. Küryakyn will pass on all warranties made by the manufacturer and where possible, will expedite the claim on behalf of the customer, but  ultimately, responsibility for disposition of the warranty claim lies with the manufacturer.

ABOUT OUR CATALOG

For purchasing Küryakyn® products, you can receive a complete catalog free of charge.
Send the Proof9of9Purchase below with your address to: Küryakyn, P.O. Box 339, Somerset, WI 54025.
Please indicate either Accessories Catalog for Harley9Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other Küryakyn® products, the motorcycle parts and accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights reserved.

Kuryakyn.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>