BUFFALO CD605 Planetary Mixer Instruction Manual

BUFFALO CD605 Planetary Mixer Instruction Manual

Safety Tips

THE PLANETARY MIXER IS A DANGEROUS APPLIANCE AND MUST ONLY BE USED BY TRAINED PERSONNEL IN ACCORDANCE WITH THESE INSTRUCTIONS

Position on a flat, stable surface.

• A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components on this product.
  • Consult Local and National Standards to comply with the following:
  • Health and Safety at Work Legislation
  • BS EN Codes of Practice
  • Fire Precautions
  • IEE Wiring Regulations
  • Building Regulations
• Always stand BEHIND the safety guard when operating the appliance.
• DO NOT place hands near the rotating attachments when in use. This can result in severe injury.
• DO NOT remove food from the appliance until the mixing attachments have come to a complete stop.
• DO NOT immerse the appliance in water.
• DO NOT attempt to mix items that this machine is not designed for. This can damage the mixing attachments.
• DO NOT use with a damaged mixing attachment.
• DO NOT bypass the safety interlocks.
• Always switch off and disconnect the power supply to the appliance when not in use.
• NEVER leave the appliance unattended when in use.
• The appliance is heavy. Take care when moving.
• This appliance must only be used in accordance with these instructions and by persons competent to do so.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Keep all packaging away from children. Dispose of the packaging in accordance to the regulations  of local authorities.
• If the power cord is damaged, it must be replaced by an BUFFALO agent or a recommended qualified technician in order to avoid a hazard.

Product Description

CD605 – 10 litre planetary mixer
CD606 – 20 litre planetary mixer
CD607 – 30 litre planetary mixer

The BUFFALO Planetary Mixer is a freestanding machine that consists of a large bowl mounted below a motor and gearbox arrangement to which a mixing tool can be attached.

Introduction

The BUFFALO Planetary Mixer has been designed to mix a range of foodstuffs, varying from cream to dough.

Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your BUFFALO product.

Pack Contents

The following is included:

• BUFFALO Planetary Mixer
• Mixing Bowl
• Spiral Dough Hook
• Beater
• Whisk
• Instruction Manual

BUFFALO prides itself on quality and service, ensuring that at the time of packaging the contents are supplied fully functional and free of damage. Should you find any damage as a result of transit, please contact your BUFFALO dealer immediately.

Installation

Ensure the location of the Planetary Mixer is capable of supporting its weight.

WARNING: The Planetary Mixer is very heavy, care must be taken when moving it.

Assembly

WARNING: The bowl must be attached and raised into position prior to starting the Planetary Mixer.

BUFFALO accept no responsibility for any injury caused by incorrect assembly of this appliance.

Note: Ensure the feet are level to reduce vibration during operation.

Remove the appliance from all packaging.

Fitting/Removing the Bowl

1. Turn Off the appliance.
2. Open the safety guard by turning it to the left (CD605 & CD606) or lifting it above the mixer (CD607).
3. Lower the bowl with the bowl handle.
4. Release the locking catches either side of the bowl.
5. Lift the bowl. The bowl is held in place by two pins securing the handles to the cradle and a hole at the back of the appliance which houses the lug on the bowl lip.
6. Reverse the procedure to fit the bowl.

Note: Ensure the handle is fully pushed back and the bowl is completely raised or the mixer will not work.

Changing the Mixer Attachment

1. Turn Off the appliance.
2. Open the safety guard by turning it to the left (CD605 & CD606) or lifting it above the mixer (CD607).
3. Lower the bowl with the bowl handle.
4. Push the mixer attachment up and to the left to release it.
5. Insert the desired attachment. Push up and to the right to lock it into place.
6. Raise the bowl.

BUFFALO recommend the following uses for each attachment:

| Spiral Dough hook| Heavy mixes dough, pie pastry etc.| Suitable Gears: 1 Slow
---|---|---|---
| Beater| Firm mixeslight pastry, cake/biscuit mix, icings, fillings and mashed vegetables| Suitable Gears: 1, 2 Medium
| **** Whisk| **** Light mixeswhipped cream, mayonnaise, egg whites, pancakes and soufflés| **** Suitable Gears: 1, 2, 3 Fast
---|---|---|---

Layout of Controls

ON button – Press to start the mixer.
OFF button – Press to stop the mixer. Twist clockwise to release and reset (CD607 only).
GEAR LEVER – Use to adjust the speed of the mixer.

Operation

Note: Ensure that these instructions have been read thoroughly and the operation of the appliance is fully understood before use
All personnel must be fully trained on the operation and safety precautions of the Planetary Mixer.

Mixing
WARNING: Always ensure the appliance is turned off before placing hands in the mixing bow

1. Open the safety guard.

2. Fill the bowl.

3. Select the desired speed and close the guard
   Note: BUFFALO recommend that you start with the slowest speed and increase the speed gradually as necessary. Ensure the safety guard is fully closed or the mixer will not work.

4. Press the START button to begin mixing
   Note: If the appliance is straining to mix then turn the appliance Off and remove some of the contents of the bowl before restarting

Changing Mixing Speed

Note: ALWAYS stop the mixer before attempting to change the mixing speed.
With the appliance turned Off:

1. Select the required gear using the gear change lever.
2. Restart the appliance.

Overload Switch

The Overload switch is situated at the back of the machine beside the cable entry. If the appliance becomes too hot the Overload switch will stop the machine automatically. If this happens:

1. Turn Off the mixer.
2. Reduce the load in the mixing bowl.
3. Push the Overload switch back in to reset it.
4. Allow the appliance to cool for 20 minutes

Note: In the event of a power cut the Overload switch will cut in to prevent the appliance from restarting automatically when power is restored.
Note: Always disconnect the Planetary Mixer from the mains powers supply when not in use.

Cleaning, Care & Maintenance

• Always turn off the mixer and disconnect from the power supply before cleaning.
• Use warm soapy water to clean the bowl and mixing attachments. Do not use abrasive cleaning chemicals as these can leave harmful residues.
• Clean the exterior of the appliance with a damp cloth.
• Dry all parts thoroughly after cleaning.
• Do not use jet/pressure washers to clean the appliance.
• Clean the appliance regularly.

Troubleshooting

If your BUFFALO appliance develops a fault, please check the following table before making a call to the Helpline.

plugged in correctly and switched on
The Stop button not released (CD607)| Turn button clockwise to release
Plug and lead are damaged| Call BUFFALO agent or qualified Technician
Fuse in the plug has blown| Replace the fuse
Power supply| Check power supply
The overload switch has activated| See overload switch information in the Operation section of this manual
Safety Guard not closed| Close Safety Guard fully
Appliance not in gear| Put in gear
Bowl not fully raised| Ensure the Bowl lever is pushed back fully
Bowl will not fit back in to place| Bowl pins or surrounding area clogged with mix| Clean the appliance
The appliance is overheating| The mixing bowl is overloaded| Turn off the appliance and empty some of the contents
The appliance has been operating for too long| Turn off the appliance and allow to cool down for 30 minutes
The appliance is noisy| Bowl or mixing attachment not correctly fitted| Remove and refit bowl/mixing attachment
Worn bearings/damaged gears| Call BUFFALO agent or qualified Technician
The mixing attachment fails to rotate properly| The belt has become loose| Call BUFFALO agent or qualified Technician
Cannot select gear| Gearing cogs misaligned| Turn Off appliance and manually turn the whisk attachment slightly. Select the gear again.

Technical Specifications

Model| Voltage| Power| Current| Dimensions w x d x h mm| Weight| Bowl Volume
---|---|---|---|---|---|---
CD605| 230V 50Hz| 500W| 2A| 485 x 410 x 635| 76kg| 10l
CD606| 230V 50Hz| 1100W| 4.7A| 560 x 540 x 765| 107kg| 20l
CD607| 230V 50Hz| 1500W| 6.5A| 700 x 620 x 1200| 208kg| 30l

Electrical Wiring

This appliance is supplied with a 3 pin, moulded, BS1363 plug and lead, with a 3 amp fuse as standard.
The plug is to be connected to a suitable mains socket. This appliance is wired as follows:

• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
• Earth wire (coloured green/yellow) to terminal marked E

This appliance must be earthed, using a dedicated earthing circuit.

If in doubt consult a qualified electrician.

Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible.

Compliance

The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.

BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities.

BUFFALO products have been approved to carry the following symbol:

DECLARATION OF CONFORMITY

• Equipment Type
  Planetary Mixer__

• Model: CD605 / CD606 / CD607

• Serial Number:___

• Year of Manufacture:

• Application of Council Directives(s):

  • EMC Directive 2004/108/EC
  • LVD Directive 2006/95/EC
  • Machinery Directive 2006/42/EC

• Standards :

  • EN55014-1:2000+A2:2002, EN61000-32:2000,
  • EN61000-3-3:1995+A1:2001, EN60335-2-64:2002
  • EN60335-1:2002, EN55014-2:1997+A1:2001,
  • BS EN 454:2000

• Producers Name : BUFFALO

• Producers Address:

  • Fourth Way
  • Avonmouth
  • Bristol
  • BS11 8TB
  • United Kingdom

I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s) and Standard(s).

• Date: 27/01/2009

• Signature

• Full Name: Richard Cromwell

• Position: Marketing Director

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>