BUFFALO DF825 Induction Hob Instruction Manual

BUFFALO DF825 Induction Hob

Safety Instructions

• Position on a flat, stable surface.

• A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components on this product.

• Consult Local and National Standards to comply with the following:

  • Health and Safety at Work Legislation
  • BS EN Codes of Practice
  • Fire Precautions
  • IEE Wiring Regulations
  • Building Regulations

• Caution! Hot surface!

• DO NOT immerse the appliance in water.

• DO NOT leave the appliance unattended during operation.

• DO NOT move the appliance during cooking or with hot cookware on top of it.

• DO NOT use cookware with a diameter less than 12cm.

• DO NOT place empty cookware on the appliance.

• DO NOT place any magnetic objects on the glass surface during operation.

• DO NOT place metal objects/utensils on the appliance as they may become hot during operation.

• People with a pacemaker fitted should not use the appliance and keep a minimum of 60cm from the appliance during operation.

• Always switch off and disconnect the power supply to the appliance when not in use.

• Not suitable for outdoor use.

• If the glass surface is cracked disconnect from the power supply and consult your Buffalo agent or recommended qualified technician.

• Keep all packaging away from children. Dispose of the packaging in accordance with the regulations of local authorities.

• If the power cord is damaged, it must be replaced by a Buffalo agent or a recommended qualified technician in order to avoid a hazard.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have
  been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.

• Buffalo recommends that this appliance should be periodically tested (at least annually) by a Competent Person. Testing should include, but not be limited to Visual Inspection, Polarity Test, Earth Continuity, Insulation Continuity, and Functional Testing.

• non-ionizing electromagnetic radiation.

• Buffalo recommends that this product is connected to a circuit protected by an appropriate RCD (Residual Current Device).

Pack Contents

The following is included:

• Buffalo Touch Control Single Induction Hob – 3kW
• Instruction manual

Buffalo prides itself on quality and service, ensuring that at the time of unpacking the contents are supplied fully functional and free of damage. Should you find any damage as a result of transit, please contact your Buffalo dealer immediately.

Induction Cooking
Induction cooking is a very efficient method of cooking as it reduces heat loss between the pan and the atmosphere by as much as 40%. This makes it extremely energy efficient, as well as offering immediate heat-up, unlike traditional heating methods which require time to get to temperature. The Induction cooker works by creating a magnetic field within suitable cookware, which causes an instant build-up of heat to cook the food.

Installation

Place the unit on a heat-resistant surface. Avoid placing it on or close to easy flammable materials. Maintain a distance of 20cm (7 inches) between the appliance and walls or other objects for ventilation.

Cookware

Suitable cookware includes:

• All magnetic pans such as Vogue Stainless Steel or Triwall pans.
• Mild steel or plain steel (black iron) pans
• Enamelled/non-enameled cast iron and iron pans
• Cookware diameter: 12cm – 20cm

Unsuitable cookware includes:

• Cookware with a diameter of less than 12cm
• Ceramic or glass cookware
• Stainless steel with no/weak magnetism, aluminum, bronze, or copper cookware unless marked as suitable for induction cooking
• Cookware with feet
• Cookware with a rounded bottom (e.g. wok)

Control Panel

Operation

1. Place suitable cookware on to the centre of the glass plate.

2. Connect the appliance to the mains power supply. The On/Off indicator light starts to flash.

3. Press the On/Off key to turn the appliance on. Heating indicator light and temperature indicator light start to flash.

4. Press the FUNCTION key and your appliance will start to work with the default power level “2000” (w) shown on the display.
   NOTE: If unsuitable cookware or no cookware is present the appliance will beep constantly before switching off. The appliance will work by either running at a Power level or a Temperature. When running at a fixed temperature, the power to the pan will reduce as the pan heats up.

5. Press the FUNCTION key to cycle between the Power and Temperature functions.

6. Press the Increase or Decrease key to change the level of each function.
   Function| Level| Increments| Default
   ---|---|---|---
   Power| 100w to 3000w| 100w/200w/300w| 2000w
   Temperature| 60°C to 240°C| 20°C| 100°C

7. To turn appliance off, just press the On/Off key.

   • To lock the control panel, press the lock key once. To unlock, press and hold the lock key.
   • This appliance has an overheat protection function. If the pan becomes too hot the appliance will switch off, a buzzer will sound and the display will show “E2”. Should this happen, allow the appliance to cool before restarting.
   • Fan will continue to run while the glass surface temperature is over 80°C.

Using the timer

• When in Power or Temperature mode, press the TIMER key to enter/view the timer.
• Press the Increase or Decrease key to change the timer.
  Function| Level| Increments| Default
  ---|---|---|---
  Timer| 0 to 180min| 5min| 0min
• When the set time expires, the appliance will switch off automatically.

Cleaning, Care & Maintenance

Disconnect from the power supply and allow the appliance to cool before cleaning.

• Use warm, soapy water and a damp cloth to clean the appliance.
• DO NOT use abrasive cleaners or pads.
• Dry thoroughly after cleaning.
• A Buffalo dealer or qualified technician should carry out repairs if required.

Troubleshooting

plugged in correctly and switched on
Plug or lead is damaged| Replace Plug or lead
Fuse in the plug has blown| Replace the plug fuse
Power supply| Check power supply
Unsuitable cookware| Replace with suitable cookware
“E0” on Display| Unsuitable cookware / no cookware| Replace with suitable cookware
“E1” on Display| Appliance has overheated| Check ventilation slots for blockage. Allow cooling before attempting to use it again.
“E2” on Display| The temperature of the pan is too high (Pan is dry or empty)| Remove cookware. Allow cooling before attempting to use it again.
“E3” on Display| Input voltage is too high/ low| Make sure the main power supply is suitable for the appliance.

Technical Specifications

Model| Voltage| Power (max.)| Current| Power range| Temperature range| Dimensions h x w x d (mm)| Weight
---|---|---|---|---|---|---|---
DF825| 220-240V

50Hz

| 3000W| 13A| 100-3000W| 60-240°C| 84 x 338 x 418| 6.6 kg

Electrical Wiring

This appliance is supplied with a 3-pin BS1363 plug and lead. The plug is to be connected to a suitable main socket.

This appliance is wired as follows:

• Live wire (colored brown) to the terminal marked L
• Neutral wire (colored blue) to the terminal marked N

If in doubt consult a qualified electrician. Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required, they must be readily accessible.

Compliance
The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of
this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.

Caterlite parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities. Caterlite products have been approved to carry the following symbol:

All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Buffalo.

Every effort is made to ensure all details are correct at the time of going to press, however, Buffalo reserves the right to change specifications without notice.

DECLARATION OF CONFORMITY

Voltage Directive (LVD) – 2014/35/EU Electrical Equipment (Safety) Regulations 2016**

EN 60335-1:2012 +A11:2014 +A13:2017 +A1:2019 +A14:2019 +A2:2019 EN 60335-2-36:2002 +A1: 2004 +A2: 2008 +A11:2012

EN 62233:2008

**Electro-Magnetic Compatibility (EMC) Directive 2014/30/EU – recast of 2004/108/EC Electromagnetic Compatibility Regulations 2016 (S.I. 2016/1091)**

EN 55014-1:2017

EN 55014-2:2015

EN IEC 61000-3-2:2019

EN 61000-3-3:2013 +A1:2019

Restriction of Hazardous Substances Directive (RoHS) 2015/863 amending Annex II to Directive 2011/65/EU

Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 (S.I. 2012/3032)

Producer Name| Buffalo

the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s), and Standard(s)

Contact No:

UK|

+44 (0)845 146 2887

---|---
Eire
NL| 040 – 2628080
FR| 01 60 34 28 80
BE-NL| 0800-29129
BE-FR| 0800-29229
DE| 0800 – 1860806
IT| N/A
ES| 901-100 133

For More Information

http://www.buffalo-appliances.com/.

References

• Buffalo Home Page

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>