BUFFALO FS440 Variable Speed Stick Blender 300mm User Manual

BUFFALO FS440 Variable Speed Stick Blender 300mm

Safety Instructions

The blender is a dangerous appliance and must only be used by trained personnel in accordance with these instructions.

•  A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components on this product.
•  Consult Local and National Standards to comply with the following:
•  Health and Safety at Work Legislation
•  BS EN Codes of Practice
•  Fire Precautions
•  IEE Wiring Regulations
•  Building Regulations
•  The protective blade guard and shaft of this appliance are designed for submersion in liquids or half-liquid mixtures. To protect against the risk of electrical shock, never submerge any other portion of this unit in any liquid.
•  The blade is sharp – handle carefully.
•  DO NOT use with loose or damaged blades.
•  The use of accessory attachments not recommended or sold by BUFFALO may cause fire, electric shock, or injury, which will invalidate your guarantee.
•  DO NOT remove food from the appliance until the blending attachment have come to a complete stop.
•  Avoid contacting moving parts. Keep hands, hair, clothing and utensils away from blade and mixing container while operating to prevent the possibility of severe injury to persons and/or damage to the appliance.
•  DO NOT operate the unit if damaged.
•  DO NOT use jet/pressure washers to clean the appliance.
• DO NOT attempt to blend items that this machine is not designed for. This can damage the blending attachments.
•  Always switch off and disconnect the power supply to the appliance when not in use, before cleaning and before putting on or taking off parts.
•  Not suitable for outdoor use.
•  Keep all packaging away from children. Dispose of the packaging in accordance to the regulations of local authorities.
•  If the power cord is damaged, it must be replaced by a BUFFALO agent or a recommended qualified technician in order to avoid a hazard.
•  This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
•  Children should be supervised to ensure that they do not play with the appliance.
•  DO NOT let the cord hang over the edge of the table or counter, or touch hot surfaces.
•  BUFFALO recommends that this appliance should be periodically tested (at least annually) by a Competent Person. Testing should include, but not be limited to: Visual Inspection, Polarity Test, Insulation Continuity and Functional Testing.
•  BUFFALO recommends that this product is connected to a circuit protected by an appropriate RCD (Residual Current Device).

Product Description

• FS440 – Buffalo
• Variable Speed Stick
• Blender – 300mm
• FS441 – Buffalo Variable
• Speed Stick Blender – 400mm
• FS442 – Buffalo Variable
• Speed Stick Blender – 500mm

Introduction

Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your BUFFALO product. This appliance is intended for use in kitchens of restaurants, canteens, and so on when mixing and liquidizing and giving soups and sauces a perfect consistency. The unit can be used directly in a container to mix everything from fish soups, stews, creams, and salad dressings to pancake mixes, pastes, sauces, mayonnaise, and the alike.

Pack Contents
The following is included:

•  Power pack
•  Detachable shaft with triangle blade pre-mounted
•  Emulsifying blade
•  Blade removal kits
•  Instruction manual

BUFFALO prides itself on quality and service, ensuring that at the time of unpacking the contents are supplied fully functional and free of damage. Should you find any damage as a result of transit, please contact your BUFFALO dealer immediately.

Operation

Assembly

•  Disconnect the power pack from the power supply.
•  Clean all removable parts thoroughly.

1. Align and insert the pins on the power pack into the notches on the shaft.
2.  Screw the cuff of the shaft as arrow shown onto the power pack until secured in place.

Blending

1. Ensure the ON/OFF button (3) is in the released position.
2.  Select speed using the variable speed dial (1).
3. Connect the appliance to the power supply.
4.  Press and hold the safety button (2) with one hand.
5. Press and hold the ON/OFF button to start the blender. Now you can release the safety button.
6. To stop the blender, just release the ON/ OFF button. The safety button will release automatically

Continuous blending
Follow steps1 to 5 as above, then:

1. While the ON/OFF button is in the depressed position, press the LOCK button (4).
2. Now release the ON/OFF button. The appliance will function continuously.
3. To stop the appliance, just press the ON/OFF button
   •  For greater control, we recommend holding the blender by the handle and the bottom of the power pack. Furthermore, it is recommended to tilt the bender slightly to prevent the blade guard from touching the bottom of the container.
   • Always make sure that the blade guard is sufficiently immersed to avoid splashing and that the air vents of the motor unit do not come into contact with any liquid. For optimum efficiency, two-thirds of the shaft should be immersed during preparation.
   • During use, the stainless steel shaft may become hot. Take care not to touch it.
   • It is advisable to start at a low speed.

Removing the lodged food
If a piece of food gets lodged in the protective blade guard surrounding the metal blade, please follow the instructions below:

1.  Turn off the blender, disconnect it from the power supply and let it come to a complete stop.
2.  Remove the shaft from the power pack.
3. Use a spatula to carefully remove the food lodged in the blade guard. The blade is sharp – Never attempt to use fingers to remove any lodged object.
   Re-attach the shaft, plug the unit back in, and continue blending.

Changing the blade

•  Warning: Before removing the blade, ensure to turn off the blender, disconnect it from the power supply and let it come to a complete stop.
•  The blade is sharp – handle carefully.
• A triangle blade is pre-mounted on the shaft.
• A round emulsifying blade is also supplied, ideal for use with nursery/special diets to prepare pur of vegetables, porridge, raw carrot purée, fruit creams, etc. To use it:
  1. Remove the shaft from the power pack.
  2. Using the triangle blade removal kit, with the round end holding the shaft top while the triangle end covers the blade then unscrewing, remove the triangle blade from the shaft.
  3. Mount the emulsifying blade securely using the emulsifying blade removal kit.

Troubleshooting

A qualified technician must carry out repairs if required.

Cleaning, Care & Maintenance

Warning: Always ensure to disconnect the unit from the power supply, let it cool down and come to a complete stop before cleaning.

•  After use, clean in time to prevent food from sticking to surfaces.
•  Clean the power pack surface using a damp cloth. Always wipe dry after cleaning. Never immerse the motor part in water or rinse it under running water.
•  Do not allow any moisture to enter the interior via any ventilation slots.
•  The appliance contains on user-serviceable parts. A BUFFALO dealer or qualified technician should carry out repairs if required.

Cleaning the shaft, blade guard, and blade

• Remove the food residue as much as possible.
•  Place the shaft and blade guard into a container with water, then switch on for a few seconds for thorough cleaning.
• WARNING: Always dry the blades well after cleaning to avoid spotting.
•  It is vital to clean thoroughly between each job using a detergent or disinfectant but never use pure bleach. For plastic parts, do not use detergents that are too alkaline.

Technical Specifications

Note: Due to our continuing program of research and development, the specifications herein may be subject to change without notice.

Electrical Wiring
This appliance is supplied with a 3-pin BS1363 plug and lead. The plug is to be connected to a suitable main socket. This appliance is wired as follows:

•  Live wire (colored brown) to the terminal marked L
•  Neutral wire (colored blue) to the terminal marked N

If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required, they must be readily accessible.

Compliance
The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.
BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities. BUFFALO products have been approved to carry the following symbol: All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of BUFFALO. Every effort is made to ensure all details are correct at the time of going to press, however, BUFFALO reserve the right to change specifications without notice.

References

• Buffalo Home Page

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>