BUFFALO FS440 Stick Blender Instruction Manual

: June 4, 2024
: BUFFALO

Table of Contents

BUFFALO FS440 Stick Blender
Safety Instructions
Product Description
Introduction
Pack Contents
Operation
- Changing the blade
Cleaning, Care & Maintenance
Troubleshooting
Technical Specifications
Electrical Wiring
Compliance
DECLARATION OF CONFORMITY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BUFFALO FS440 Stick Blender

BUFFALO-FS440-Stick-Blender-product

Safety Instructions

The blender is a dangerous appliance and must only be used by trained personnel in accordance with these instructions.

A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components on this product.
Consult Local and National Standards to comply with the following:
- Health and Safety at Work Legislation
- BS EN Codes of Practice
- Fire Precautions
- IEE Wiring Regulations
- Building Regulations
The protective blade guard and shaft of this appliance are designed for submersion in liquids or half-liquid mixtures. To protect against risk of electrical shock, never submerge any other portion of this unit in any liquid.
Blade is sharp – handle carefully.
DO NOT use with loose or damaged blades.
The use of accessory attachments not recommended or sold by BUFFALO may cause fire, electric shock, or injury, which will invalidate your guarantee.
DO NOT remove food from the appliance until the blending attachment have come to a complete stop.
Avoid contacting moving parts. Keep hands, hair, clothing and utensils away from blade and mixing container while operation to prevent the possibility of severe injury to persons and/or damage to the appliance.
DO NOT operate the unit if damaged.
DO NOT use jet/pressure washers to clean the appliance.
DO NOT attempt to blend items that this machine is not designed for. This can damage the blending attachments.
Always switch off and disconnect the power supply to the appliance when not in use, before cleaning and before putting on or taking off parts.
Not suitable for outdoor use.
Keep all packaging away from children. Dispose of the packaging in accordance to the regulations of local authorities.
If the power cord is damaged, it must be replaced by a BUFFALO agent or a recommended qualified technician in order to avoid a hazard.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
DO NOT let cord hang over edge of table or counter, or touch hot surfaces.
BUFFALO recommend that this appliance should be periodically tested (at least annually) by a Competent Person. Testing should include, but not be limited to: Visual Inspection, Polarity Test, Insulation Continuity and Functional Testing.
BUFFALO recommend that this product is connected to a circuit protected by an appropriate RCD (Residual Current Device).

Product Description

FS440 – Buffalo Variable Speed Stick Blender – 300mm FS441 – Buffalo Variable Speed Stick Blender – 400mm FS442 – Buffalo Variable Speed Stick Blender – 500mm

Introduction

Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your BUFFALO product. This appliance is intended for use in kitchens of restaurants, canteens and so on when mixing and liquidising and giving soups and sauces a perfect consistency. The unit can be used directly in a container to mix everything from fish soups, stews, creams and salad dressings to pancake mixes, pastes, sauces, mayonnaise and alike.

Pack Contents

The following is included:

Power pack
Detachable shaft with triangle blade pre-mounted
Emulsifying blade
Blade removal kits
Instruction manual

BUFFALO prides itself on quality and service, ensuring that at the time of unpacking the contents are supplied fully functional and free of damage. Should you find any damage as a result of transit, please contact your BUFFALO dealer immediately.

Operation

BUFFALO-FS440-Stick-Blender-fig-1

Assembly
Before assembly, ensure to

Disconnect the power pack from the power supply.
Clean all removable parts thoroughly.

Align and insert the pins of the shaft into the lock sleeve of the power pack.
Screw the shaft as arrow shown into the power pack securely.

Blending

Ensure the ON/OFF button (3) is in the released position.
Select speed using the variable speed dial (1).
Connect the appliance to the power supply.
Press and hold the safety button (2) with one hand.
Press and hold the ON/OFF button to start the blender. Now you can release the safety button.
To stop the blender, just release the ON/OFF button. The safety button will release automatically.

Continuous blending
Follow steps1 to 5 as above, then:

While the ON/OFF button is in the depressed position, press the LOCK button (4).
Now release the ON/OFF button. The appliance will function continuously.
To stop the appliance, just press the ON/OFF button once.

For greater control, we recommend holding the blender by the handle and the bottom of the power pack. Furthermore, it is recommended to tilt the bender slightly to prevent the blade guard from touching the bottom of the container.
Always make sure that the blade guard is sufficiently immersed to avoid splashing and that the air vents of the motor unit does not come into contact with any liquid. For optimum efficiency, two thirds of the shaft should be immersed during preparation.
During use, the stainless steel shaft may become hot. Take care not to touch it.
It is advisable to start at a low speed.

Removing the lodged food
If a piece of food gets lodged in the protective blade guard surrounding the metal blade, please follow the instructions below:

Turn off blender, disconnect from power supply and let it come to a complete stop.
Remove the shaft from the power pack.
Use a spatula to carefully remove the food lodged in the blade guard. The blade is sharp – Never attempt to use fingers to remove any lodged object.
Re-attach the shaft, plug unit back in and continue blending.

Changing the blade

Warning : Before removing blade, ensure to turn off blender, disconnect from power supply and let it come to a complete stop.
Blade is sharp – handle carefully.
A triangle blade is pre-mounted on the shaft.
A round emulsifying blade is also supplied, ideal for use with nursery/special diets to prepare purée of vegetables, porridge, raw carrot purée, fruit creams, etc. To use it:

Remove the shaft from the power pack.
Using the triangle blade removal kit, with the round end holding the shaft top while the triangle end covering the blade then unscrewing, remove the triangle blade from the shaft.
Mount the emulsifying blade securely using the emulsifying blade removal kit.

Cleaning, Care & Maintenance

Warning : Always ensure to disconnect unit from power supply, let it cool down and come to a complete stop before cleaning.

After use, clean in time to prevent food from sticking to surfaces.
Clean the power pack surface using a damp cloth. Always wipe dry after cleaning. Never immerse the motor part in water or rinse it under running water.
Do not allow any moisture to enter the interior via any ventilation slots.
The appliance contains on user serviceable parts. A BUFFALO dealer or qualified technician should carry out repairs if required.

Cleaning the shaft, blade guard, and blade

Remove the food residue as much as possible.
Place the shaft and blade guard into a container with water, then switch on for a few seconds for thorough cleaning.
WARNING : Always dry the blades well after cleaning to avoid spotting.
It is vital to clean thoroughly between each job using a detergent or disinfectant, but never use pure bleach. For plastic parts, do not use detergents that are too alkaline.

Troubleshooting

A qualified technician must carry out repairs if required.

Fault	Probable Cause	Solution
The unit is not working	The unit is not switched on	Check the unit is

plugged in correctly and switched on
Plug or lead is damaged| Replace plug or lead
Fuse in the plug has blown| Replace the plug fuse
Mains power supply fault| Check mains power supply
Unit stops working suddenly| Overheating protection is activated| Release the ON/OFF button, then unplug. Wait a few minutes for the motor to cool down and the thermal safety mechanism to reset, then restart
Loud noise| Blade not correctly fitted| Release the ON/OFF button, then unplug. Re-install the blade

Technical Specifications

Model| Voltage| Power| Current| Blending Capacity| Shaft length| Dimensions h x Ø mm| Weight
---|---|---|---|---|---|---|---
FS440| 220-240V~

50Hz

| 500W| 2.2A| 60L| 300mm| 708 x 100| 3.60kg
FS441| 500W| 2.2A| 100L| 400mm| 808 x 100| 4.00kg
FS442| 500W| 2.2A| 120L| 500mm| 908 x 100| 4.20kg

Electrical Wiring

This appliance is supplied with a 3 pin BS1363 plug and lead. The plug is to be connected to a suitable mains socket. This appliance is wired as follows:

Live wire (coloured brown) to terminal marked L
Neutral wire (coloured blue) to terminal marked N

If in doubt consult a qualified electrician. Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible

Compliance

The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area. BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities. BUFFALO products have been approved to carry the following symbol All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of BUFFALO. Every effort is made to ensure all details are correct at the time of going to press, however, BUFFALO reserve the right to change specifications without notice.

DECLARATION OF CONFORMITY

Equipment Type

| Model
---|---
Variable speed stick blender – 300mm Variable speed stick blender – 400mm Variable speed stick blender – 500mm| FS440 (& -E) FS441 (& -E) FS442 (& -E)
Application of Territory Legislation & Council Directives(s)

| Machinery Directive 2006/42/EC

The Supply of Machinery (Safety) Regulations 2008

EN ISO 12100:210

EN 60204-1:2018

EN 12853:2001 +A1:2010

Electro-Magnetic Compatibility (EMC) Directive 2014/30/EU – recast of 2004/108/EC Electromagnetic Compatibility Regulations 2016 (S.I. 2016/1091)

EN 55014-1:2017

EN 55014-2:2015

EN IEC 61000-3-2:2019

EN 61000-3-3:2013 +A1:2019

Restriction of Hazardous Substances Directive (RoHS) 2015/863 amending Annex II to Directive 2011/65/EU

Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic

Equipment Regulations 2012 (S.I. 2012/3032)

Producer Name| Buffalo

I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s) and Standard(s).