RYNOSKIN RSSS-FB4D-56 Running Boards Installation Guide
- June 13, 2024
- RYNOSKIN
Table of Contents
RYNOSKIN RSSS-FB4D-56 Running Boards
Product Information
- Product Name: Python Side Step
- Part Number: RSSS-FB4D-56
- Fits: 2021-Up Ford Bronco 4 Door
- Installation Time: 90-180 minutes
- Cutting: Not Required
- Drilling: Not Required
Part List:
- Driver/Left Side Front Bracket
- Passenger/Right Side Front Bracket
- A Bigger Notch Here
- Driver/Left Side Center Bracket
- Passenger/Right Side Center Bracket
- Driver/Left Side Rear Bracket
- Passenger/Right Side Rear Bracket
- A Smaller Notch Here
- x12 10mm x 30mm Hex Bolt
- x12 10mm Flat Washer
- x12 10mm Lock Washer
- x12 8mm x 25mm Combo Bolt
Tools Required:
- Wrench: 10mm, 13mm, 16mm, 18mm
- Allen Wrench: 4mm, 5mm, 6mm, 8mm
Product Usage Instructions
- Before Installation:
- Remove contents from the box and verify that all parts are present according to the parts list.
- Read the instructions carefully.
- Assistance is recommended, especially if cutting is required.
- Step 1: Starting from underneath the Passenger/Right body panel, locate the front mounting location and the threaded holes in the body panel. Remove the plastic plugs covering the holes.
- Step 2: Attach the Passenger/Right Front Mounting Bracket to the front location using (2) 10mm Hex Bolts, (2) 10mm Lock Washers, and (2) 10mm Flat Washers. Do not tighten the hardware.
- Step 3: Repeat Steps 1-2 to attach Passenger/Right Center and Rear Mounting Brackets to the center and rear locations. Note: There is a Bigger Notch on the rear of the Center Brackets and a Smaller Notch on the bottom of the Rear Brackets. Do not tighten the hardware.
- Step 4: Select the Passenger/Right Running Board. Carefully place the Running Board on the brackets. Attach the Running Board to the (3) Mounting Brackets using (6) 8mm Combo Bolts. Do not tighten the hardware.
- Step 5: Level and adjust the Running Board, then fully tighten all hardware.
- Step 6: Repeat Steps 1-5 to attach the Driver/Left Running Board.
- Step 7: Periodically inspect the installation to ensure that all hardware is secure and tight.
Contact Information:
- Customer Support: service@rynoskinauto.com.
- Website: www.rynoskinauto.com.
Torque & Tools
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT DEPEND ON THE PARTS LIST. READ INSTRUCTIONS CAREFULLY. CUTTING MAY BE REQUIRED. ASSISTANCE IS RECOMMENDED.
Part List
Hardware
INSTALLATION
PLEASE NOTE THAT THE FOLLOWING PICTURES ARE BASED ON THE PASSENGER-SIDE INSTALLATION
STEP 1
Starting from underneath the Passenger/Right body panel, locate the front
mounting location and the threaded holes in the body panel, (Fig 1). Remove
the plastic plugs covering the holes.
STEP 2
Select the Passenger/Right Front Mounting Bracket. Attach the Mounting Bracket
to the front location with (2) 10mm Hex Bolts, (2) 10mm Lock Washers and (2)
10mm Flat Washers, (Fig 2). Do not tighten hardware.
STEP 3
Repeat Steps 1-2 to attach Passenger/Right Center and Rear Mounting Brackets
to the center and rear locations, (Figs 3-6). NOTE: There is a Bigger Notch on
the rear of the Center Brackets and a Smaller Notch on the bottom of the Rear
Brackets. Do not tighten the hardware.
(Fig 4) Attach (1) Passenger/Right Center Mounting Bracket to the center location.
Note: A Bigger Notch on the rear of the Center Brackets
(Fig 6) Attach (1) Passenger/Right Rear Mounting Bracket to the Rear location.
Note: A Smaller Notch on the bottom of the Rear Brackets
STEP 4
Select the Passenger/Right Running Board.
NOTE:
The Passenger/Right Running Board will have a “56-P” on the front. Carefully
place the Running Board on the brackets. Attach the Running Board to the (3)
Mounting Brackets with (6) 8mm Combo Bolts, (Fig 7). Do not tighten the
hardware.
STEP 5
Level and adjust the Running Board and fully tighten all hardware.
STEP 6
Repeat Steps 1—5 to attach the Driver/Left Running Board.
STEP 7
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
Attention
- To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish.
- Mild soap may be used also to clean the Running Boards.
Contact Information
- Website: www.rynoskinauto.com.
- Customer Support: service@rynoskinauto.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>