Skydance RM1 RF Dimmer Remote Control Instruction Manual
- June 13, 2024
- SKYDANCE
Table of Contents
Skydance RM1 RF Dimmer Remote Control
Product Information
The 6-Key RF Remote Controller Model No.: RM1/RM2 is a wireless remote controller designed for dimming and color temperature control of single color or dual color LED controllers. It operates on a 2.4GHz RF signal and has a remote distance of up to 30m in a barrier-free space. The remote is powered by a CR2032 battery and features an LED indicator light for easy operation. The RM1 model is specifically designed for 1 zone dimming, while the RM2 model is designed for 1 zone color temperature control.
Mechanical Structures and Installations:
The dimensions of the RM1/RM2 6-Key RF Remote Controller are as follows:
- Length: 47.00 mm
- Width: 8.00 mm
- Height: 100.00 mm
The remote controller can be used with compatible LED controllers and should be installed in a dry indoor location.
Technical Parameters:
- Input and Output: RF(2.4GHz)
- Output Signal: 3VDC(CR2032)
- Working Voltage: 5mA
- Working Current: 2A
- Standby Current: 2 years
- Remote Distance: 30m (Barrier-free space)
The operating temperature range is from -30°C to +55°C, and the IP rating is IP20.
Safety and EMC:
The 6-Key RF Remote Controller conforms to the following standards and certifications:
- EMC Standard (EMC): ETSI EN 301 489-1 V2.2.3
- Safety Standard (LVD): ETSI EN 301 489-17 V3.2.4, EN 62368-1:2020+A11:2020
- Radio Equipment (RED) Certification: ETSI EN 300 328 V2.2.2 CE, EMC, LVD, RED
Warranty:
The 6-Key RF Remote Controller comes with a warranty period of 5 years.
Product Usage Instructions
Match Remote Control (two match ways)
The end user can choose one of the two options for matching the remote control:
Option 1: Use the controller’s Match key
- Short press the match key on the controller.
- Immediately press the On/Off key on the remote control.
If the LED indicator on the remote control fast flashes a few times, it means the match is successful.
To delete all matched remotes:
- Press and hold the match key on the controller for 5 seconds.
If the LED indicator on the remote control fast flashes a few times, it means all matched remotes were deleted.
Option 2: Use Power Restart Match
This option is useful when the remote control is not responding or the remote distance has become smaller and insensitive.
- Switch off the power.
- Switch on the power.
- Repeat steps 1 and 2.
- Immediately short press the On/Off key 3 times on the remote control.
If the light blinks 3 times, it means the match is successful.
To delete all matched remotes:
- Switch off the power.
- Switch on the power.
- Repeat steps 1 and 2.
- Immediately short press the On/Off key 5 times on the remote control.
If the light blinks 5 times, it means all matched remotes were deleted.
Key Function
RM1 1 zone dimming remote:
- On/Off: Turns the light on or off. Long press for 2 seconds will turn off the light after 60 seconds.
- 50% brightness: Sets the brightness to 50%.
- 30s: Turns off the light after 30 seconds.
- 10% brightness for small night light: Sets the brightness to 10% for a small night light.
- Brightness+/-: Short press to adjust the brightness in 10 levels. Long press for 1-6 seconds for continuous adjustment with 256 levels.
RM2 1 zone CCT remote:
- On/Off: Turns the light on or off. Long press for 2 seconds will turn off the light after 60 seconds.
- Color temperature+: Increases the color temperature.
- 30s: Turns off the light after 30 seconds.
- Color temperature-: Decreases the color temperature.
- Brightness+/-: Short press to adjust the brightness in 10 levels. Long press for 1-6 seconds for continuous adjustment with 256 levels.
Safety Information:
- Read all instructions carefully before installation.
- Pay attention to the battery’s positive and negative polarity when installing the battery.
- If the remote control is not used for a long time, remove the battery.
- If the remote distance becomes smaller and insensitive, replace the battery.
- Gently handle the remote control to avoid falling.
- For indoor and dry location use only.
6-Key RF Remote Controller
Model No.: RM1/RM2
1 zone dimming/6-key/Wireless remote 30m distance/CR2032 battery
Features
- Apply to single color or dual color LED controller.
- Each remote can match one or more receiver.
- CR2032 battery powered.
- Operate with LED indicator light
Technical Parameters
Input and Output
Output signal| RF(2.4GHz)
Working voltage| 3VDC(CR2032)
Working current| ＜5mA
Standby current| ＜2μA
Standby time| 2 years
Remote distance| 30m(Barrier-free space)
Safety and EMC
EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED
Environment
Operation temperature| Ta: -30 OC ~ +55 OC
IP rating| IP20
Mechanical Structures and Installations
Match Remote Control (two match ways)
End user can choose the suitable match/delete ways. Two options are offered for selection:
Use the controller’s Match key
-
Match:
Short press match key, immediately press on/off key on the remote. The LED indicator fast flash a few times means match is successful -
Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted
Use Power Restart
-
Match:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key 3 times on the remote. The light blinks 3 times means match is succes -
Delete:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key 5 times on the remote. The light blinks 5 times means all matched remotes were deleted
Key function
RM1 1 zone dimming remote
Brightness+/-:
Short press 10 levels, long press 1-6s for continuous 256 levels adjustment
RM2 1 zone CCT remote
-
Color temperature+/-:
Short press 11 levels, long press 1-6s for continuous 256 levels adjustment. -
Brightness+/-:
Short press 10 levels, long press 1-6s for continuous 256 levels adjustment.
Safety information
- Read all instructions carefully before you begin this installation.
- When installing battery, pay attention to the battery positive and negative polarity. A long time without the remote control, remove the battery. When remote distance becomes smaller and insensitive, replace the battery.
- If no response from the receiver, please re-match the remote.
- Gently handle remote, beware of falling.
- For indoor and dry location use only.
Warranty
- Warranty 5 years
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>