KICHLER 52685CPZ Carston 2 Light 19 Wide Picture Light Instruction Manual

KICHLER 52685CPZ Carston 2 Light 19 Wide Picture Light

FIXTURE DIAGRAM

PARTS LIST

• [A] Shade
• [B] Adjustment Screw
• [C] Knob (2)
• [D] Lock Washer (2)
• [E] Canopy
• [F] Mounting Screw (2)
• [G] Mounting Strap
• [H] Strap Mounting Screw (2)
• [I] Outlet Box (not supplied)

CAUTIONS

• RISK OF SHOCK:
  Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

• This fixture is intended for use with LED Bulb(s) ONLY.

WARNING:

1. This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

• Always be certain that electric current is turned off before cleaning.
• Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

1. Remove knobs[C] and lock washers[D] from the mounting screws that are preinstalled to mounting strap[G]. Retain knobs and lock washers.

2. Attach mounting strap[G] to outlet box[I] using the strap mounting screws[H]. Mounting strap can be adjusted to suit position of fixture.

3. Grounding instructions: (See Illus. a or b).

   • On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
   • On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap.
     Fixture is provided with two (2) ground wires. Connect fixture ground wires to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.

4. Make wire connections. Reference chart below for correct connections and wire accordingly.
   Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
   ---|---
   Black| White
   Parallel cord (round & smooth)| Parallel cord (square & ridged)
   Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
   Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)

5. NOTE: Fixture can be installed in the down position (light shines downward) or up position (light shines upward).
   Push fixture to wall, carefully aligning the mounting screws protruding from the mounting strap with holes in canopy.
   NOTE: Make sure all wires are inside canopy and do not get pinched between mounting strap and canopy, or wall and canopy of fixture.

6. Slip lock washers[D] over threads protruding through holes in canopy (2 places).

7. Screw knobs[C] onto threads protruding through holes in canopy (2 places) and tighten to secure fixture to wall.

8. Adjust shade[A] (Fig. 1) by loosening adjustment screw[B] at the fixture joint (turn slightly counterclockwise), adjusting shade to desired position, then re-tightening adjustment screw (turn slightly clockwise). DO NOT COMPLETELY REMOVE THE ADJUSTMENT SCREW FROM THE FIXTURE JOINT.

9. Insert recommended LED bulb(s) (not included).

For warranty information please visit: kichler.com/warranty

We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>