BROCK Electronics MG 1601 RD Meat Grinder with Accessories Instruction Manual
- June 5, 2024
- BROCK Electronics
Table of Contents
BROCK Electronics MG 1601 RD Meat Grinder with Accessories Instruction
Manual
MG 1601 RD, MG 1601 SS
MG 1601 RD, MG 1601 SS
SAFETY CONDITIONS
- Household use only. Do not use for industrial purpose.
- Unplug from outlet when assembling and disassembling the unit.
- Close supervision is necessary when any appliance is used near children.
- When carrying the unit be sure to hold the motor housing with both hands. Do not carry the unit by holding only the hopper plate or head.
- Do not fix the cutting blade and cutting plate when using kibbe attachment.
- Never feed food by hand. Always use food pusher.
- Do not grind hard food such as bones, nuts, etc.
- Do not grind ginger and other materials with hard fiber.
- Continuous running of meat grinder should be not more than 10 minutes with the following 10 minutes interval for motor cooling.
- Reverse function is prohibited while the appliance is operating (For example switch“ON” knob to “R” knob or on the contrary), wait at least 5 seconds until grinder has come to a complete stop，otherwise it may cause an abnormal noise, vibration or a transitory electric spark in the appliance. It could result easily damage to appliance and make a user frightened.
- After use, there would be a little food left in the grinder head. This is normal. There might be a bit of black metal powder adhering to the food ground in the end. Please pick them out and throw away, do not eat them.
- To avoid jamming, do not force to operate the unit with excessive pressure.
- When the circuit breaker activates, do not switch on.
- Never try to replace the parts and repair the unit by yourself.
- This appliance is not intended for use by persons (including children) with reduce physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard。
- Children should be supervised to ensure that they do not play with the appliance.
DESCRIPTION
- Food pusher
- Hopper plate
- Unlock button
- ON/O/R (ON/OFF/ REVERSE)
- ON/R Switch
- Pusher of vegetable shredder
- Head of vegetable shredder
- Cutter of vegetable shredder
- Head
- Feed screw
- Cutting blade
- Cutting plate (fine)
- Cutting plate (medium)
- Cutting plate (coarse)
- Fixing ring
- Sausage attachment
- Kibbe attachment
- Head inlet
FOR THE FIRST TIME
Check that voltage indicated on the rating label corresponds the mains voltage
in your home. Wash all parts (except body) in warm soapy water. Before
plugging in, ensure the “ON/0/ R” switch is turned to “O” position
INSTRUCTION FOR USE
ASSEMBLING
MINCING MEAT
Cut all foods into pieces (Sinewless, boneless and fatless meat is
recommended, approximate size :20 mm x 20 mm x 60 mm) so that they fit easily
into the hopper opening. Plug in and turn the “ON / R” switch to ” ON”
position, then turn the “ON/0/ R” switch to “ON” position.
Feed foods into the hopper plate. Use only the food pusher (fig.7).
After use switch the unit off and unplug it from the power supply.
Grind the mixture three times.
Disassemble by reversing the steps from 5-3 to remove the cutting plate and
cutting blade.
Place kibbe attachments onto the feed screw shaft together, fitting
protrusions in the slots (fig.8).
Screw Big fixing ring into place until tight. Do not over tighten (fig.9).
Make the cylindrical outlet cover (fig.10).
Form kibbe as illustrated below and deep fry.
MAKING SAUSAGE
Before starting please assemble sausage attachment as per following (fig.11)
CUTTING SLICE/SHRED/STRIP
Press the fasten button，hold the head and insert it into the inlet(when
inserting please pay
attention the head must be slanted as per arrow indicated on the top),then
move the head
anticlockwise so that the head being fastened tightly . There will be locked
when you heard a
voice of “KA”. (fig.12)
Put the cutting attachments “slice cutter” or “Shredded cutter” or “strip
cutter” into the cutting
head. Note: Must be on place.(fig.13)
The switch ON/R knob to “ON”, the switch ON/0/R knob to “ON” position when you cutting. Put the vegetable into vegetable cutting head, and then push down the vegetable pusher with 5N After use switch the unit off and unplug it from the power supply.
CLEANING AND MAINTENANCE
DISASSEMBLING
Make sure that the motor has stopped completely.
Disconnect the plug from the power outlet.
Disassemble by reversing the steps from 6-1 pictures.
If the Big fixing ring is not easily removed by hands, please use tools
（fig.15.
To remove the cutting plate easily, place a screwdriver between the cutting
plate and the head as illustrated and lift it up (fig.16).
Press the unlock button before removing the head. Holding the head, rotate it
in the same direction as fig.17. Then the head can be removed easily.
CLEANING
Before you clean the appliance, switch the appliance off and remove the plug
from the socket.
Never clean the accessories by a dishwasher with strong alkaline cleaner, a
bleaching solution containing chlorine will discolor aluminum surfaces.
Remove meat, etc. Wash each part in warm soapy water.
Do not immerse the motor housing in water, but only wipe it with a damp cloth.
Thinners and petrol will crack or change the color of the unit.
Wash all the metal parts in water below 50℃ and dry.
Wipe all the cutting parts by vegetable oil -wet cloth.
In case the unit is left unused for a long period of time, wipe all the metal
parts by vegetable oil
cloth.
TECHNICAL INFORMATION
Rated Voltage………………………………………………………………………. 220-240 V
Nominal Frequency……………………………………………………………… 50-60 Hz
Rated Power……………………………………………………………………….. 1400 W
INFORMATION FOR USERS FOR THE USE OF ELECTRICAL AND ELECTRONIC DEVICES
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
This product meets all the basic requirements of EU directives related to it.
Trademarks BROCK Electronics owner GTCL BALTIC
Phone: +371 67297762
E-mail: gtcl@gtcl.eu
www.brockgroup.eu
www.gtcl.eu
Technical Service: Tel. +371 28683856,
serviss@gtcl.eu
Warranty card
Model name: MG 1601 SS / MG 1601 RD
S/N:
Serial number
Prinz Eugen-Straße1040 Wien, Österreich www.brockelectronics.eu
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>