MINKA LAVERY 3150-77 14 In 3 Light Candelabra E 12 Base Chandelier Instruction Manual
- June 13, 2024
- MINKA LAVERY
Table of Contents
MINKA LAVERY 3150-77 14 In 3 Light Candelabra E 12 Base Chandelier
Product Information
The product is a fixture item with the model number 3150-77. It was manufactured on March 31, 2021. The fixture is designed for indoor use and requires a power supply from a fuse box or circuit breaker. The fixture can accommodate three candelabra base bulbs up to 60 watts each or CFL or LED equivalents. The maximum wattage rating should not be exceeded to ensure safe usage. The fixture comes with a chain for hanging crystal drops and chains, as well as a collar ring and canopy for installation. The package includes necessary mounting hardware such as a crossbar, ground screw, and mounting screws.
Product Usage Instructions
- Before starting the installation, ensure that the power to the fixture is shut off at the fuse box or circuit breaker.
- Remove the old fixture and its mounting hardware.
- Thread the fixture loop (J) onto all thread (K) until snug.
- Install three candelabra base bulbs up to 60 watts each or CFL/LED equivalents according to the fixture specification. Do not exceed the maximum wattage rating.
- Thread all thread (S) into collar loop (T) until snug.
- Thread the other end of all thread (S) into the crossbar (P).
- Place a lock washer (Q) and hex nut (R) over the end of all thread (S) protruding through the crossbar (P), then tighten the hex nut (R) to all thread (S) until snug.
- Mount the crossbar assembly to the ceiling outlet box (V) using outlet box screws (W). Ensure that the side of the crossbar marked GND faces out.
- Use proper chain pliers to open one end link of the chain and connect it to the fixture loop (A). Close the link.
- Determine the correct number of links needed for the desired hanging height. Use chain pliers to disconnect and discard the remaining chain.
- Carefully place the fixture wires through the chain (X).
- Slip the collar ring (Y) and canopy (U) over the chain (X).
- Open the other end link of the chain (X) and connect it to the collar loop (T). Close the link.
- Feed the fixture wires through the collar loop (T) and all thread (S) and pull until tight.
- Connect the electrical wires according to the provided diagram (Fig. 3). Ensure that all wire connectors are secured.
- If your outlet box has a ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the crossbar (P) using the green screw provided.
- Tuck wire connectors neatly into the ceiling outlet box.
- Raise the canopy (U) over the crossbar assembly and secure it with the collar ring (Y).
- Hang crystal drops (A and G) onto the fixture (I) as shown in Fig. 1.
- Hang crystal chains (B, C, D, E, F) onto the fixture as shown in Fig. 1.
- After completing the installation, restore power to the outlet box and test the fixture.
Note:
It is important to use proper chain pliers (not included) to open and close
the chain provided with the fixture. Do not use other tools that may twist or
stress the chain links. Refer to the provided diagram for proper chain pliers.
WARNING!
SHUT POWER OFF A T FUSE OR CIRCUIT BREAKER.
ASSEMBLING THE FIXTURE
ASSEMBLING THE FIXTURE (FIG. 1)
- Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
- Shut off the power at the fuse box or circuit breaker. If necessary, remove the old fixture including the mounting hardware.
- Thread fixture loop (J) onto all thread (K) until snug.
- Install (3) three candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. —DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
Code
|
Glass#
| QTY/per item
---|---|---
A| GC3150-A| 20
B| GC3150-B| 1
C| GC3150-C| 1
D| GC3150-D| 1
E| GC3150-E| 1
F| GC3150-F| 1
G| GC3150-G| 1
MOUNTING THE FIXTURE
MOUNTING THE FIXTURE (FIG. 2)
- Thread all thread (S) into collar loop (T) until snug.
- Thread the other end of all thread (S) into the crossbar (P).
- Place lock washer (Q) and hex nut (R) over the end of all thread (S) protruding through crossbar (P), then thread hex nut (R) to all thread (S) until snug.
- Take this crossbar assembly and mount it to the ceiling outlet box (V) using outlet box screws (W). The side of the crossbar marked “GND” must face out.
- Use proper chain pliers to open one end link of the chain and connect to the fixture loop (A). Close the link.
- By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the remaining chain.
- Carefully place the fixture wires through the chain (X).
- Slip collar ring (Y) and canopy (U) over the chain (X).
- Open the other end link of the chain (X) and connect to the collar loop (T). Close the link.
- Feed the fixture wires through the collar loop (T) and all thread (S) and pull until tight.
CONNECTING THE WIRE
CONNECTING THE WIRE (See Fig. 3)
- Connect the electrical wires as shown in Fig. 3, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the crossbar (P) using the green screw provided.
- Tuck wire connectors neatly into the ceiling outlet box. Raise canopy (U) over the crossbar assembly and secure with collar ring (Y).
HANG THE CRYSTAL DROPS (FIG. 1)
- Hang crystal drops (A and G) onto fixture (I) as shown in Fig 1.
- Hang crystal chains (B&C&D&E&F) onto the fixture as shown in Fig 1.
Your installation is now complete. Return power to the outlet box and test the fixture.
Notice:
It is important to use proper chain pliers (not included) to OPEN and CLOSE
the chain included with this fixture. Do not open them with other tools that
may twist or stress the chain links. It is important to use proper chain
pliers like the ones shown in the diagram.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>