CMACEWHEEL YL91F-V Electric Bike Display User Manual

: June 5, 2024
: CMACEWHEEL

Table of Contents

Product Name and Model Number
Specification
Appearance and Size
Function overview and Functional areas
Routine operation
Personalized parameter settings
Shortcut operation
- Restore factory settings operation
- Trip odometer reset operation
Quality Assurance and Warranty
- Warranty info
- Warranty does not cover
Wire connection diagram
- Standard wire connection sequence
Precautions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CMACEWHEEL YL91F-V Electric Bike Display

Product Name and Model Number

Smart LCD display for electric bicycle; Model: YL91F-V.

Specification

36V/48V/52V power supply
Display rated current 15mA
Display maximum current 30mA
Shutdown leakage current <1uA
Supplied current to the controller 50mA
Operating temperature -20～60℃
Storage temperature -30 to 70°C3.

Appearance and Size

Figure 3-1 Physical picture of the YL91F-V display

Function overview and Functional areas

Functional overview

The YL91F-V display offers a variety of features to suit your riding needs, including

Battery level indicator
Pedal assist (PAS) level indicator
Speed (current speed, maximum speed, average speed)
Mileage display (single and total mileage)
Walk boost mode
Light ON/OFF
Error code indicator
Motor power indicator (optional)
USB connection indicator (optional)
Cruise control indicator (optional)
Bluetooth connection indicator (optional)
Personalized parameter settings (e.g. wheel diameter, speed limit, battery power setting and PAS parameter setting, password setting, controller current limit setting, etc.).
Factory default parameter recovery function

Functional areas

Button definitions

The YL91F-V display is equipped with five buttons on the corresponding operating unit: power on/off , plus ,minus , light and toggle .

Routine operation

Power on/off

Long press to power on/off the display. When the display is off, it will not use the battery power and the leakage current is less than 1uA.

The display will automatically shut off if it is not used for more than 10 minutes.

Display interface switching

When the display is powered on, it will show the Current Speed (km/h) and Odometer (km) by default. Short press to switch between Odometer (km), Trip Odometer(km), Maximum Speed (km/h), and Average Speed (km/h).

Figure 5-1 Display Interface Switching

Walk boost mode

Long Press and hold , the electric bicycle enters the walk boost mode. The electric bicycle will walk at a fixed speed of 6 km per hour and the display shows state before walk boost. . Release the button to stop the power output immediately and restore to the state before walk boost.

The walk boost mode can only be used when pushing the electric bicycle, please do not use it while riding.

Turning on/off lights

Press the to make the controller turn on the lights and the display backlight becomes dim. Press again to make the controller turn off the lights and the backlight restore brightness.

PAS level selection

Press / to switch PAS level of electric bicycle, thus changing the motor output power.

Figure 5-4 PAS level display interface

Battery level display

The Battery level is shown as 5 bars. When the battery is full charged, all of the 5 bars lighten up. When the battery is fully depleted, the bar will begin to flash, warning the user to charge the battery as soon as possible.

Error code display

If there is a fault occurs in the electronic system of the electric bicycle, the display will automatically show an error code, see Schedule 1 for a detailed definition of the error code.

When the error code appears on the display, please troubleshoot the problem in time, the electric bicycle will not be able to drive normally after the problem occurs.

Personalized parameter settings

Each setting needs to be done with the bicycle stationary.
The personalized parameter setting procedure is as follows:

When the display is ON and the speed shows 0,

Press and hold simultaneously for more than 2 seconds to enter the personalized parameter setting interface.
Press / changing state. to toggle between the personalized parameter setting interface, and press to enter the parameter
Press / to select the parameter, long pres for addition operation, long press for subtraction operation.
Press to save the parameter settings and return to the personalized parameter setting interface.
Long Press to save the parameter settings and exit the personalized parameter setting interface. The following options are available on the personalized parameter setting interface:

Metric and Imperial setting

P1 is the metric and imperial setting, 00 for metric and 01 for imperial.

Press to enter the parameter changing state. Press the / to select the parameter and press to save the parameter setting and return to the personalized parameter setting interface.

Rated voltage setting

P2 is the rated voltage setting. The available rated voltage range is: 24V, 36V, 48V, 52V.

Press to enter the parameter changing state. Press the / to select the parameter and press to save the parameter setting and return to the personalized parameter setting interface.

PAS level setting

P3 is the Pedal assist (PAS) level setting. The available Pedal assist level settings are: 0~3, 1~3, 0~5, 1~5, 1~7, 0~7, 0~9, 1~9.

Press to enter the parameter changing state. Press the / to select the parameter and press to save the parameter setting and return to the personalized parameter setting interface.

Wheel diameter setting

P4 is the wheel diameter setting. The adjustable wheel diameter range is: 1~50inch.
Press to enter the parameter changing state. Press the / to select the parameter and press to save the parameter setting and return to the personalized parameter setting interface.

Number of speed sensor magnets setting

P5 is the speed sensor magnet number setting. The adjustable speed sensor magnet number range is: 1 ~ 100 pcs.
Press to enter the parameter changing state. Press the / to select the parameter and press to save the parameter setting and return to the personalized parameter setting interface.

Speed Limit Setting

P6 is the speed limit setting. The adjustable speed limit range is: 1~100km/h. (The maximum adjustable speed limit varies by different protocols)
Press to enter the parameter changing state. Press the / to select the parameter and press to save the parameter setting and return to the personalized parameter setting interface.

Start-up setting

P7 is the start-up setting. The display can choose the following start modes: 00zero start, 01non-zero start.
Press to enter the parameter changing state. Press the / to select the parameter and press to save the parameter setting and return to the personalized parameter setting interface.

Drive mode setting

P8 is the drive mode setting. The available drive modes are: 00→Pedal assist only, 01→Electric only, 02→Both Pedal assist and electric.
Press to enter the parameter changing state. Press the / to select the parameter and press to save the parameter setting and return to the personalized parameter setting interface.

Pedal assist sensitivity setting

P9 is the pedal assist sensitivity setting. When set to higher numbers, it will take more crank rotations to activate the motor. On lower numbers, it will take little crank rotation to activate the motor. The adjustable range is: 1~24.
Press to enter the parameter changing state. Press the / to select the parameter and press to save the parameter setting and return to the personalized parameter setting interface.

Pedal assist strength setting

PA is the Pedal assist strength setting. The Pedal assist strength is the relative strength of the PWM signal from the controller when start to activate pedal assist. The adjustable range is 0 ~ 5. 0 is the weakest strength and 5 is the strongest.

Press to enter the parameter changing state. Press the / to select the parameter and press to save the parameter setting and return to the personalized parameter setting interface.

Number of pedal assist sensor magnets setting

Pb is the number of pedal assist sensor magnets setting. The adjustable range: 1~15 pcs.
Press to enter the parameter changing state. Press the / to select the parameter and press parameter setting and return to the personalized parameter setting interface.

Controller Current Limit Setting

PC is the controller current limit setting. The adjustable range is: 1~50A.
Press to enter the parameter changing state. Press the / to select the parameter and press to save the parameter setting and return to the personalized parameter setting interface.

Battery under voltage value setting

Pd is the battery under voltage setting. The value can be adjusted based on the current rated voltage.
Press to enter the parameter changing state. Press the / to select the parameter and press to save the parameter setting and return to the personalized parameter setting interface.

Power-on password setting

PE is the power-on password setting. The power-on password is not activated by default but users can activate it from setting PSd-y. The factory default password is 1212. Users can set other four-digit password. Please keep the password in mind after changing it, otherwise you will not be able to use the display.

Press to enter the parameter changing state. Press the / to select the parameter. PSd-y means the power-on password is activated while PSd-n is off. Press to confirm the mode and enter the state of setting the four digits power-on password or exit to the personalized parameter setting interface.

In the password setting mode, the adjustable digit will flash. Press the / to select the parameter and press to save the numbers and go to the next digit setting. Long press to save the parameter setting and return to the personalized parameter setting interface after finishing setting the four digits in turn.

Auto Sleep Time Setting

PF is the auto sleep time setting. To save the battery power and reach higher range, this display will be turned off after it has not been used for a time. The adjustable range is: 1~60min, 00 means no auto shutdown. The factory default setting is 10 minutes.
Press to enter the parameter changing state. Press the / to select the parameter and press to save the parameter setting and return to the personalized parameter setting interface.

Shortcut operation

Restore factory settings operation

dEF is the restore factory default parameter settings. dEF-Y is to restore the factory default settings, and dEF-N is not to restore.
Enter into the main setting interface and keep the speed at 0, press and hold and simultaneously for 2s to enter the restore factory default setting interface. Pressing / to toggle to dEF-Y. Then after pressing to confirm, the display will show dEF-0 for a few seconds and then automatically start to restore the factory default settings. The display will automatically exit to setting interface after the restoration.

Trip odometer reset operation

The display can record trip odometer and odometer. Trip odometer is not automatically reset after turning off. The trip odometer needs to be reset manually. The odometer can not be reset.
Enter into the main setting interface and keep the speed at 0, press and hold and simultaneously for 2s to reset the trip odometer. The main interface will flash during the reset process.

Quality Assurance and Warranty

Warranty info

Yolin will offer a limited warranty for any failure caused by the product defects under normal use during the warranty period.

Warranty does not cover

The shell is opened.
The connector is damaged.
Scratches on the appearance after the product is out of factory.
Scratched or broken wires
Failure or damage caused by force majeure (e.g. fire, earthquake, etc.) or natural disaster (e.g. lightning strike, etc.)
Out of warranty period.

Wire connection diagram

Standard wire connection sequence

Table 9-1 Standard connector wire sequence table

Standard Wire Sequence

| Standard wire color|

Function

---|---|---
1| Red (VCC)| Display power wire
2| Blue (Kp)| Controller power wire
3| Black (GND)| Display ground wire
4| Green (RX)| Display data reception wire
5| Yellow (TX)| Display data transmit wire

Some models are equipped with waterproof connectors and the color inside wires can not be seen.

Precautions

Pay attention to all the general operating when using the products and do not plug and unplug the display while it is powered on.

Avoid bumping the display as much as possible.
Please do not change the parameter settings at will, otherwise normal riding cannot be guaranteed.
If display does not work properly, please send it to the repair center as soon as possible.
There may be differences between the physical products and this manual due to normal upgrade. Please refer to the physical products.

Schedule 1: Error Code Definition

YL-01, YL-02 Error codes

breakdown

YL-05, KDS, YL-J Error codes

Schedule 2: Pedal assist level default ratio value

Level
Level selection| 1| 2| 3| 4| 5| 6| 7| 8| 9
---|---|---|---|---|---|---|---|---|---
0-3/1-3| 50%| 74%| 92%| –| –| –| –| –| –
0-5/ 1-5| 50%| 61%| 73%| 85%| 96%| –| –| –| –
0-7/ 1-7| 40%| 50%| 60%| 70%| 80%| 90%| 96%| –| –
0-9/ 1-9| 25%| 34%| 43%| 52%| 61%| 70%| 79%| 88%| 96%

Email:info@cmacewheel.com
Website:www.cmacewheel.com