alora WV347104 Wall Lamp Instruction Manual

: June 13, 2024
: aLora

Table of Contents

alora WV347104 Wall Lamp
Product Information
Product Usage Instructions
ASSEMBLY INSTRUCTIONS
ABOUT COMPANY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

alora WV347104 Wall Lamp

alora-WV347104-Wall-Lamp-FIG-1

Product Information

Model Number	WV347104
Product Name	Wall Lamp
Technical Support	1.855.855.8926
Email Support

technicalsupport@aloralighting.com
Manufacturer Website| www.aloralighting.com
Manufacturer Address (Canada)| 19054 28th Avenue Surrey – BC V3Z 6M3
Manufacturer Address (USA)| 3035 E. Lone Mountain Rd – Las Vegas, NV, 89081

Product Usage Instructions

Remove the fixture from its original package.
Separate the mounting plate (1c) from the canopy (2a) by removing the canopy screws (2b).
Attach the mounting plate (1c) to the electrical junction box (1a) using the junction box screws provided (1e) in the hardware package.
Make proper electrical connections by using wire nuts (1b) provided in the hardware package. Connect the black wire to hot L, white wire to neutral N, and ground wire to GND. Place the driver (4a) in the canopy (2a).
Secure the filament (5c) to the fixture (5b) by threading it clockwise. Attach the filament end (5d) to the filament (5c) using the end cap (5e). Align the holes on the fixture (5b) and filament end (5d) with the holes on the shade (6b), then secure them with screws (6a).
Secure the canopy (2a) to the mounting plate (1c) using the canopy screws (2b).
Use the dimmer switch (3a) to turn the lamp on/off.
Use the lock (5a) to unlock the fixture and adjust its tilt. Lock it in place once adjusted.
You are now ready to enjoy your wall lamp.

WARNINGS AND CAUTIONS

Make sure POWER is COMPLETELY OFF at the fuse box
Have your fixture installed by a qualified licensed electrician
Prepare everything in a clear area
Wear gloves at all times during this installation
Read instructions carefully before you start assembly
Keep this installation sheet for future reference

Please Note:

This Alora LED fixture comes with pre-wired LED module(s)
Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage
For dimming, an ELV (Electronic Low Voltage) or TRIAC type of dimmer is required
120V input

NOTICE

The important safeguards and instructions outlined in this sheet cannot cover all possible conditions and situations that may occur. It must be understood that caution and certain care factors must be followed. These instructions are provided for your safety and we highly recommend that a licensed, trained electrician install this unit.
This fixture is designed to be mounted on a correctly installed standard round or octagon box OR through a wiring box with a plaster frame. The box must be securely mounted to the structure of the building. The crossbar and hardware supplied should be used, directly mounting the fixture to the outlet box may make it impossible to correctly align the fixture.

ASSEMBLY INSTRUCTIONS

Step 1
Remove fixture from its original package.
Step 2
Separate mounting plate (1c) from canopy (2a) by removing canopy screws (2b).
Step 3
Attach mounting plate (1c) to electrical junction box (1a) using junction box screws provided (1e) in hardware package.
Step 4
Make proper electrical connections (black to hot “L”, white to neutral “N”, ground to “GND”) with wire nuts (1b) provided in hardware package and place driver (4a) in canopy (2a).
Step 5
Secure filament (5c) to fixture (5b) by threading clockwise. Attach filament end (5d) to filament (5c) with end cap (5e). Align holes on fixture (5b) and filament end (5d) with holes on shade (6b), secure with screws (6a).
Step 6
Secure canopy (2a) to mounting plate (1c) with canopy screws (2b).
Step 7
Use dimmer switch (3a) to turn on/off.
Step 8
Use lock (5a) to unlock fixture to adjust tilt and lock in place.
You are now ready to enjoy your fixture.