auna 10036342 Spacewoofer DAB + Boombox User Manual

: June 5, 2024
: Auna

Table of Contents

TECHNICAL DATA
SAFETY INSTRUCTIONS
PRODUCT DESCRIPTION AND CONTROLS
POWER SOURCE
REMOTE CONTROL
BASIC FUNCTIONS
RADIO (FM & DAB)
CD/MP3
USB
BT
AUX-IN
DISPOSAL CONSIDERATIONS
DECLARATION OF CONFORMITY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

auna 10036342 Spacewoofer DAB + Boombox User Manual

Dear Customer,

Congratulations on purchasing this equipment.
Please read this manual carefully and take care of the following hints to avoid damages. Any failure caused by ignoring the items and cautions mentioned in the instruction manual is not covered by our warranty and any liability. Scan the QR code to get access to the latest user manual and other information about the product:

TECHNICAL DATA

Item number 10036341 10036342
Power supply AC 100-240 V ~ 50/60 Hz
DC 12V UM-C x 8 pcs

Power consumption (Watt) 30 W
Standby consumption (Watt) 0,5 W
Receiver frequency range FM 87.5 – 108 MHz
CD player frequency range 100 Hz – 16 KHz
BT reach Up to 10 meters
DAB/DAB+ 174.928 – 239.200 MHz (Band III)
Operation temperature + 5°C – + 35° C

Connectors
AUX IN input 3.5 mm
Headphone (jack plug) 3.5 mm
USB port

SAFETY INSTRUCTIONS

This device may only be used by children from the age of 8 and up and by persons with reduced physical, sensory and mental capabilities or a lack of experience and / or knowledge if they are supervised or have been instructed in the safe use of the device and have understood the resulting dangers.
Cleaning and user maintenance should not be done by children unless they are 8 years of age or older and are supervised.
Children must not play with the device.
Observe all notes listed in the operating instructions.
Do not use the unit near water or in a humid environment.
Make sure that no liquid is spilled over the unit and the unit openings.
Move the unit carefully to avoid damaging it.
Do not block the device outputs.
Do not place the unit near heat sources (e.g. heating). Do not expose the device to direct sunlight.
Plug the power plug of the unit into the power outlet in the manner intended.
The device is equipped with overload protection. Should this need to be replaced, contact customer service or a similarly qualified person.
Unplug the unit from the wall outlet if it will not be used for a long period of time.
Do not attempt to service or repair the unit yourself. In this case, the warranty expires.
The mains plug is used to disconnect the device from the mains after it has been switched off. Make sure that the mains plug is always freely accessible.
Do not expose the device to splash water or place objects filled with liquid, such as vases, on the device.
Do not expose the batteries to extreme heat such as sunlight or fire.
Do not obstruct the ventilation of the unit by blocking the ventilation openings with objects such as newspapers, tablecloths, curtains, etc..
Ensure that a minimum distance of 5 mm to all sides of the unit is maintained.
Do not place sources of open flame ignition, such as lit candles, on the unit.
Dispose of used batteries in an environmentally friendly manner.
Use the device only in temperate climate, not in tropical climate.

WARNING
Risk of injury! To reduce the risk of electric shock, do not open either the cover or the back of the unit. The device does not contain any parts that could be serviced by the customer. Please contact customer service or similarly qualified personnel for maintenance and repair.

PRODUCT DESCRIPTION AND CONTROLS

1	USB port
2	AUX IN jack
3	Phones jack
4	FOLD.+/+10/MEM.+ Button

(Scroll up in folders/lists/memory list)

5| FOLD.-/-10/MEM.- Button

(Scroll down in folders/lists/memory list)

6| Volume Knob
7| PROG./P-MODE/MEM. Button

(Program selection/Programming mode/Memory)

POWER SOURCE

This unit is designed to be operated on AC/DC.

AC Operation

Plug the tail of supplied AC power cord into AC socket on unit and the plug into household AC outlet. The batteries will be automatically disconnected.

DC Operation

Open the battery compartment door. Install 8 pcs UM-2 “C” size batteries (not included) into compartment. Please follow correct polarities as indicated.

Note: When using battery, take off the AC cable from unit.
Remove batteries if they are flat or not being used for a long period of time.
Batteries contain chemical substances, so they should be disposed of properly.

ESD hints – The product maybe reset or not reset to operation of control due to electrostatic discharge, just switch off and reconnect again.

REMOTE CONTROL

Key functions

FUNC (Function selection key)
MUTE
MEM (Memory key)
EQ (Tone control)
FOLD./10/M. (UP/DOWN)
(Scroll up/down in folders/lists)
Back/Fast Backward/Tuning –
Play/Pause
P-MODE/Info (Programming mode)
Stop / Menu
PAIR (BT Pairing key)
**** Next/Fast Forward/Tuning +
ID3 (Display MP3 information)
VOLUME (UP/DOWN)
LIGHT
MO/ST (Mono/stereo key)
STANDBY (On/Off key)
Remote sensor
Battery compartment

Note: Please pull battery protector before using.

Remote control operation

To operate the unit with the remote control, point the remote handset at the remote sensor on the front panel and press the appropriate button on the remote handset.
The remote works best within a range of 6 ~ 7 meters from the front panel and on an angle of 30 degrees.
Bright sunlight or room light conditions can interfere with the remote control.
If the remote operation is unsatisfactory or stops working entirely, first try replacing the remote batteries, then try reducing the room lighting conditions.

Lithium battery installation of remote control

The remote control includes one CR2025(3V) lithium battery.

To replace the battery, gently push the clasp to the right direction accordingly to the instruction and then pull out the battery compartment.
Take the drained battery out and install a new lithium battery(CR-2025) in the compartment with the positive polarity upwarded. Then push the compartment back to its position with a “click” sound indicating installation finished.

BASIC FUNCTIONS

Tuning on the unit

After connecting the power, press the Standby button (23) on unit or the STANDBY button (16) on remote control to turn on the unit.
Press the Function selection button (15) on unit or the FUNC button (1) on remote control to choose FM/CD/USB/BT/AUX function.

Note: In CD/USB/BT/AUX mode, when the unit is not providing the main function for 15 minutes, the unit will automatically switch into standby mode. Press the Standby button to turn on the unit again.

Volume control

Rotate the Volume knob (6) on unit to increase or decrease volume.

Headphone jack

If required, insert a headphone with a 3.5 mm jack plug (not included) into the headphone jack (3). The speaker (24) is automatically muted.

CAUTION:
Listening at high volume over a long period of time can damage your ears.

ID3 tag system (show MP3 info)

Some MP3 files are encoded with information such as the name of the song, the artist, and the album. Together, this information is called an “ID3 tag”.

Press and hold the EQ/ID3 button (10) on unit or the ID3 key (12) on remote control to turn the ID3 tag display on or off. When the ID3 tag display is on, the unit will display tag information in the order shown below.

EQ function (equalizer)

This unit has a built-in equalizer system.

Press the EQ/ID3 button (10) on unit or the EQ key (4) on remote control to select a different music style (sound tone): FLAT, CLASSIC, ROCK, POP, JAZZ and DBBS.

LED light

Press the Light button (9) on unit or the LIGHT key (14) on remote control to turn on the LED light and choose from 8 different flashing modes effect. To disable the LED light, press the Light button until the display shows “LIGHT OFF”.

RADIO (FM & DAB)

Tuning radio stations

Press the Function selection button (15) on unit or the FUNC key (1) on remote control to select the radio mode: FM.
Tune to desired station by rotating the Tuning knob (17) on unit, the display will show the band frequency. Example: FM 97.10 MHz. You can also press and hold the FORWARD or BACK button for fast searching, it will auto stop at any station with strong signal.
Rotate the Volume knob (6) on unit to increase or decrease volume.
Extend the telescopic antenna (22) to its full length and gently move the unit back and forth to get the best reception, or place the unit in an open location.
To turn off the radio, press the Function selection button (15) on unit or the FUNC key (1) on remote control to switch to other functions or press Standby button (8) on unit or STANDBY key (16) on remote control to turn off the unit.

Auto preset memory / scan

To search for and automatically save stations to preset memory, press and hold the Play button (16) on unit. Any station with a strong enough signal will be saved to preset memory. After the unit finishes scanning, the unit will automatically tune to preset station number 1 (P01).
To tune to the next or previous preset station, press FOLD./10/M.+/- button (4 & 5) on the unit or FOLD./10/M. (UP/DOWN) key (5) on the remote control.

Manual preset memory operation

You may pre-store 30 radio stations in memory for your preference.

Rotate the Tuning knob (17) on unit to select the desired station that you want to save as a preset.
Press the PROG./P-MODE/MEM. button (7) on unit or press MEM key (3) on remote control, “P01” will flash on the display to indicate that you are saving the station as preset memory 01. To change the preset memory sequence, press the FOLD./10/M +/- button (4 & 5) on unit or FOLD./10/M (UP/DOWN) key (5) on remote control, then press PROG./PMODE/MEM. button (7) on unit or press MEM key (3) on remote again to enter.
Search another station, repeat steps (1) and (2) until all desired stations stored. Up to 30 FM stations can be programmed.
Press the FOLD./10/M +/- button (4 & 5) on unit or FOLD./10/M (UP/ DOWN) key (5) on remote control to switch between the stored stations.

CD/MP3

Discs for Playback

This system can playback all digital audio CD/MP3, finalized digital audio CD- Recordable (CD-R) discs, finalized digital audio CD-Rewritable (CD-RW) discs and CD-DA format digital audio CD/CD-R/CD-RW discs.

LOADING A DISC

Press the Function selection button (15) on unit or the FUNC key (1) on remote control to select “CD” mode.
Press the PUSH TO OPEN button to open the CD door, “OP” will be shown on the display.
Place an audio CD/MP3 DISC into the tray with the front side facing up.
Close the CD door.
The display will show a flashing “READING”, then the total number of tracks would be shown and the playback will start from track.
To remove the CD, press Stop button (14) to turn off the unit, then press the PUSH TO OPEN button to open the CD compartment lid. Hold the CD by its edges, and take it out carefully.

Note: Make sure the disc is stopped before opening the CD door (11). To ensure good system performance, wait until the unit completely reads the disc before proceeding. If no disc loaded into the tray, or the disc is unreadable, the display will show “NO”.

Playing a disc

To pause playback, press Play/Pause button (16) on unit or Play/ Pause key (7) on remote control, the current playing time will flash on the display. To resume playback, press Play/Pause button (16) on unit or Play/Pause key (7) on remote control again.
To stop playback, press Stop button (14) on unit or (9) on remote control.

Selecting a desired track/passage

To select a desired track:

Press the FORWARD oder BACK button on stop mode or during playing until the desired track appears on the display. It will start play automatically

To search for a particular passage during playback (track scanning at high speed):

Press and hold FORWARD oder BACK button to scan the current playing track at high speed until desired point (passage) appears, then release the button for normal playback mode. Playback will start again from this point.

To select a song which track number exceeds 10 (for MP3 disc only):

To select a song/track which number exceeds 10, press the FOLD/10/M +/- button (4 & 5) on unit or FOLD/10/M (UP/DOWN) key (5) on remote control each time to skip forward or backward 10 tracks.

To select a desired folder (if the disc contains more than one folder):

To select a desired folder, press and hold the FOLD/10/M +/- button (4 & 5) on unit or FOLD/10/M (UP/DOWN) key (5) on remote control each time to skip forward or backward a folder.

Programming tracks

Programming tracks of disc is possible when playback is stopped. Up
to 20 tracks for CD disc and 99 tracks for MP3 disc can be stored in the
memory in any order.

In stop mode, press the PROG./P-MODE/MEM. button (7) on unit or
MEM key (3) on remote control to enter program setting, the PROG logo and “P01” will show on the display with “F00” flashing. Press FOLD/10/M +/- button (4 & 5) on unit or FOLD/10/M (UP/DOWN) key (5) on remote control to choose the desired folder. Press PROG./ P-MODE/MEM. (7) button on unit or MEM key (3) on remote control again to confirm. After confirming the folder, “T00” will flash on the display, press the FORWARD oder BACK button to choose the desired track to be programmed as P01, then press PROG./P-MODE/ MEM. button (7) on unit or MEM key (3) on remote control again to confirm.
Repeat step 1 to store other desired tracks until all tracks are programmed.
Press the Play button (16) on unit or the Play key on remote control to start playback from the first programmed track.
Press the Stop button (14) on unit to stop program playback.
To clear the program, you may press the Stop button (14) on unit when the disc st

Repeat play

You can play one track or all tracks on the disc repeatedly.

To Repeat a Single Track:

Press PROG./P-MODE/MEM. button (7) on unit or P-MODE key (8) on remote control during play, the display will show the symbol “ ” (REPEAT) and the current track will be played over an over again till you press the Stopp button .
To cancel repeat play, press PROG./P-MODE/MEM. button (7) on unit or P-MODE key (8) on remote control until the symbol “ ” (REPEAT) disappears from the display.

To repeat all the tracks

Press PROG./P-MODE/MEM. button (7) on unit or the P-MODE key (8) on remote control until the symbol shows steadily on the display, all tracks on the disc will be played over and over again till you press the Stop button .
To cancel repeat play, press the PROG./P-MODE/MEM. button (7) on unit or the P-MODE key (8) on remote control until the symbol disappears from the display.

To repeat the folder (only for MP3 discs which contain more than one folder):

Press the PROG./P-MODE/MEM. button (7) on unit or P-MODE key (8)on remote control until the symbol “ DIR ” (REPEAT DIR) shows steadily on the display, the current folder will be repeated over and over again till you press the Stop button .
To cancel repeat play, press the PROG./P-MODE/MEM. button (7) on unit or P-MODE key (8) on remote control until the symbol “ DIR ” (REPEAT DIR) disappears from the display.

Random play

Press the PROG./P-MODE/MEM. button (7) on unit or P-MODE key (8) on remote control in play mode till the “RAN” shows steadily on the display, the random play will start from next track automatically, until all tracks are played over and then it will stop.
Press the PROG./P-MODE/MEM. button (7) on unit or P-MODE key (8) on remote control again until the “RDM” disappears from the display to cancel.

Intro play

Press the PROG./P-MODE/MEM. button (7) on unit or P-MODE key (8) on remote control in play mode till the “INTRO” shows steadily on the display, the intro play will start and scan 10 seconds for every track.
To cancel intro play, press the PROG./P-MODE/MEM. button (7) on unit or P-MODE key (8) on remote control again until “INTRO” disappear from the display.

USB

Press the Function selection button (15) on unit to select “USB” mode.
Connect the USB device to the USB input (1). The LCD will show the total number of tracks stored in the USB. The playback starts from track 1 automatically after reading the USB.
To pause playback, press the Pair button (16) on unit or the PAIR key (10) on remote control, the current playing time will flash on the display. To resume playback, press the button again.
Press the Pair button (16) on unit or the PAIR key (10) on remote control to stop playing. The display will show total number of USB and “STOP“.
The different selection modes Proceed program play/Repeat play (repeat 1 – repeat folder – repeat all)/Random play/Intro play operation as the same described above in the “CD/MP3” section.

Note: Do not use any USB extension cable for connecting the USB device as it may cause interference.

BT

Press the Function selection button (15) on unit or the FUNC button (1) on remote control to switch to BT function, the LCD will display “BT ” and the Pair indicator (27) will flash at high speed.
Turn on the BT function on the device, scan the unit “CD228DAB” and connect, then input the password “0000“ if required, the Pair blue light will light up to indicate connection done, and the display will show “BT”. Press the Play/Pause/Pair button (16) on the unit or the Play key (7) on the remote control to start playback. If the unit can‘t connect the relative BT within 2 minutes, press the Play/Pause/Pair button (16) on unit or the PAIR key (10) on remote control to reconnect.
Rotate the Volume knob on unit or adjust the volume on the BT device to your desired level.
Press FORWARD or BACK button on the unit or on external device to choose the desired track.
To stop playback, press Play/Pause/Pair button (16) on unit or the Stop key on the external device.

Note: The Bluetooth works best within 10 meters.

AUX-IN

Press the Function selection button (15) on unit or the FUNC key (1) on remote control to select “AUX” mode.
Insert the AUX line plug into the AUX IN jack (Ø 3.5 mm) (2) on the player, music from the device would be amplified and exported from the speakers.
Adjust the volume on the unit or on the device to your desired level.
Proceed play/pause and next/previous on the device.

DISPOSAL CONSIDERATIONS

Disposal Icon
If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

This product contains batteries. If there is a legal regulation for the disposal of batteries in your country, the batteries must not be disposed of with household waste. Find out about local regulations for disposing of batteries. By disposing of them in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences.