aLora PD321708 Marni 38W LED Pendant 4.38 Inches Tall and 4.38 Inches Wide User Guide
- June 13, 2024
- aLora
Table of Contents
PD321708
Pendant
PD321708 Marni 38W LED Pendant 4.38 Inches Tall and 4.38 Inches Wide
TECHNICAL SUPPORT
1.855.855.8926
technicalsupport@aloralighting.com
**** WARNINGS AND CAUTIONS
- Make sure POWER is COMPLETELY OFF at the fuse box
- Have your fixture installed by a qualified licensed electrician
- Prepare everything in a clear area
- Wear gloves at all times during this installation
- Read instructions carefully before you start assembly
- Keep this installation sheet for future reference
Please Note:
- This Alora LED fixture comes with pre-wired LED module(s)
- Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage
- For dimming, an ELV (Electronic Low Voltage), TRIAC or 0-10V type of dimmer is required
- 120-277V input
NOTICE
- The important safeguards and instructions outlined in this sheet cannot cover all possible conditions and situations that may occur. It must be understood that caution and certain care factors must be followed. These instructions are provided for your safety and we highly recommend that a licensed, trained electrician install this unit.
ASSEMBLY INSTRUCTIONS
Step 1
Remove fixture from its original package.
Step 2
Separate mounting plate (1c) from canopy (2a) by removing canopy screws (2b).
Step 3
Attach mounting plate (1c) to electrical junction box (1a) using junction box
screws provided (1e) in hardware package.
Step 4
Make proper electrical connections (black to hot “L”, white to neutral “N”,
green to “GND”, Dim + to purple, Dim- to gray) with wire nuts provided in
hardware package.
Step 5
Attach canopy (2a) to mounting plate (1c) with canopy screws (2b).
Step 6 (For Horizontal Orientation Option)
Secure non-powered backplate (5b) to mounting surface by compressing butterfly
clips (5a) through 3/8” holes in ceiling and then use screws (5c) to fasten.
(See Illustration 1 for optional mounting option). Attach non-powered
decorative cover (6a) to non-powered backplate (5b), followed by pivot (6b)
and secure with decorative ring (6c) by threading clockwise. Align hole in
pivot (6b) and fixture end (7a) and secure with screw (6d).
Step 7 (For Vertical Orientation Option)
Remove fixture end (7a) and cut excess wire (See Illustration 2). Secure bead
end (10a) to fixture by threading clockwise (See Illustration 3)
Step 8
Remove protective paper.
You are now ready to enjoy your fixture.
Wires –
Hot (Black) —-
Neutral (White)…….
Ground (Green)===
Dim – (Gray): Optional—-
Dim + (Purple): Optional—-
Illustration 1: Optional Mounting Option
With Junction Box
Attach non-powered backplate (5b) to non powered junction box (8a)
with screws (8b).
Illustration 2
Illustration 3
P: 1.855.855.8926
19054 28th Avenue Surrey – BC V3Z 6M3
CANADA :
USA : 3035 E. Lone Mountain Rd – Las Vegas, NV, 89081
www.aloralighting.com
20230619
Documents / Resources
|
aLora PD321708 Marni 38W LED Pendant 4.38 Inches Tall and 4.38 Inches
Wide
[pdf] User Guide
PD321708 Marni 38W LED Pendant 4.38 Inches Tall and 4.38 Inches Wide,
PD321708, Marni 38W LED Pendant 4.38 Inches Tall and 4.38 Inches Wide, LED
Pendant 4.38 Inches Tall and 4.38 Inches Wide, 4.38 Inches Tall and 4.38
Inches Wide, Inches Tall and 4.38 Inches Wide, Tall and 4.38 Inches Wide,
Inches Wide
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>