alora PD321716 Natural Brass Marni 5 Inch Wide LED Linear Pendant Instruction Manual

alora PD321716 Natural Brass Marni 5 Inch Wide LED Linear Pendant

Product Information

• Product Name: Pendant
• Model Number: PD321716
• Technical Support: 1.855.855.8926
• Email : technicalsupport@aloralighting.com
• Manufacturer: Alora Lighting

Warnings and Cautions:

• It is important to follow the instructions provided for your safety.
• A licensed and trained electrician is recommended for the installation of this unit.

Assembly Instructions:

1. Step 1: Remove the fixture from its original package.
2. Step 2: Separate the mounting plate (1c) from the canopy (2a) by removing the canopy screws (2b).
3. Step 3: Attach the mounting plate (1c) to the electrical junction box (1a) using the junction box screws provided (1e) in the hardware package.

Electrical Connections:
The following electrical connections should be made with wire nuts provided in the hardware package:

• Hot (Black) – Connect to hot L
• Neutral (White) – Connect to neutral N
• Ground (Green) – Connect to GND
• Dim – (Gray) – Optional
• Dim + (Purple) – Optional

Installation :

• Step 4: Make the proper electrical connections as described above.
• Step 5: Attach the canopy (2a) to the mounting plate (1c) using the canopy screws (2b).
• Step 6: For Horizontal Orientation Option:
  • Secure the non-powered backplate (5b) to the mounting surface by compressing butterfly clips (5a) through 3/8 holes in the ceiling.
  • Use screws (5c) to fasten the backplate.
  • Attach the non-powered decorative cover (6a) to the non-powered backplate (5b).
  • Attach the pivot (6b) and secure it with the decorative ring (6c) by threading clockwise.
  • Align the hole in the pivot (6b) with the fixture end (7a) and secure it with the screw (6d).
• Step 7: For Vertical Orientation Option:
  • Remove the fixture end (7a) and cut excess wire.
  • Secure the bead end (10a) to the fixture by threading clockwise.
• Step 8: Remove the protective paper and your fixture is ready to use.

Contact Information:

• P: 1.855.855.8926
• Canada Address: 19054 28th Avenue Surrey – BC V3Z 6M3
• USA Address: 3035 E. Lone Mountain Rd – Las Vegas, NV, 89081
• Website : www.aloralighting.com
• Manufacturing Date : 20230619

TECHNICAL SUPPORT

• 1.855.855.8926
• technicalsupport@aloralighting.com

WARNINGS AND CAUTIONS

• Make sure POWER is COMPLETELY OFF at the fuse box
• Have your fixture installed by a qualified licensed electrician
• Prepare everything in a clear area
• Wear gloves at all times during this installation
• Read instructions carefully before you start assembly
• Keep this installation sheet for future reference

Please Note:

• This Alora LED fixture comes with pre-wired LED module(s)
• Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage
• For dimming, an ELV (Electronic Low Voltage), TRIAC or 0-10V type of dimmer is required
• 120-277V input

NOTICE
The important safeguards and instructions outlined in this sheet cannot cover all possible conditions and situations that may occur. It must be understood that caution and certain care factors must be followed. These instructions are provided for your safety and we highly recommend that a licensed, trained electrician install this unit.

ASSEMBLY INSTRUCTIONS

1. Step 1
   Remove fixture from its original package.

2. Step 2
   Separate mounting plate (1c) from canopy (2a) by removing canopy screws (2b).

3. Step 3
   Attach mounting plate (1c) to electrical junction box (1a) using junction box screws provided (1e) in hardware package.

4. Step 4
   Make proper electrical connections (black to hot “L”, white to neutral “N”, green to “GND”, Dim + to purple, Dim- to gray) with wire nuts provided in hardware package.

5. Step 5
   Attach canopy (2a) to mounting plate (1c) with canopy screws (2b).

6. Step 6 (For Horizontal Orientation Option)
   Secure non-powered backplate (5b) to mounting surface by compressing butterfly clips (5a) through 3/8” holes in ceiling and then use screws (5c) to fasten. (See Illustration 1 for optional mounting option). Attach non-powered decorative cover (6a) to non-powered backplate (5b), followed by pivot (6b) and secure with decorative ring (6c) by threading clockwise. Align hole in pivot (6b) and fixture end (7a) and secure with screw (6d).

7. Step 7 (For Vertical Orientation Option)
   Remove fixture end (7a) and cut excess wire (See Illustration 2). Secure bead end (10a) to fixture by threading clockwise (See Illustration 3)

8. Step 8
   Remove protective paper.

You are now ready to enjoy your fixture.

Illustration 1: Optional Mounting Option
With Junction Box

P: 1.855.855.8926
CANADA : 19054 28th Avenue Surrey – BC V3Z 6M3
USA : 3035 E. Lone Mountain Rd – Las
Vegas, NV, 89081 www.aloralighting.com
20230619

References

• Alora Lighting | A Shining light in style, quality and customer care.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>