WAC Lighting WS-61334-30-BK Loophole 34 Tall Switchable Color Temperature LED Bath Bar Instruction Manual
- June 13, 2024
- WAC LIGHTING
Table of Contents
WAC Lighting WS-61334-30-BK Loophole 34 Tall Switchable Color Temperature
LED Bath Bar
Product Information
The WS-61326/WS-61334 is a lighting fixture designed for use by Modern Forms.
It is important to use all parts and accessories as indicated in the provided
instructions. Substituting parts or accessories not designated for use with
this product could result in personal injury, property damage, and void the
warranty.
Coastal conditions may cause mineral and residue build-up on the fixture. It
is recommended that customers in coastal areas clean all external surfaces of
the fixture once every two weeks with a wet cloth.
Product Specifications
- Wire Connector Qty: 3pcs+1Extra
- Mounting Screw Qty: 1 Extra
- Mounting Ring Qty: 1pc
- Conversion Plate Qty: 1pc
Contact Information
- dweLED.com
- Phone: (800) 526.2588
- Fax: (800) 526.2585
Distribution Centers:
- Headquarters/Eastern Distribution Center – 44 Harbor Park Drive, Port Washington, NY 11050
- Central Distribution Center – 1600 Distribution Ct, Lithia Springs, GA 30122
- Western Distribution Center – 1750 Archibald Avenue, Ontario, CA 91760
Date
November 2022
Product Usage Instructions
- Shut off the power at the circuit breaker and remove the existing fixture, including the crossbar.
- Carefully unpack the new fixture and lay out all the parts on a clear area. Ensure that no small parts necessary for installation are lost.
- Loosen the mounting screw (B) from the fixture and remove the mounting back plate.
- The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch in the canopy (Fig. 4).
- Secure the mounting back plate to the switch box using junction box screws.
- Remove the mounting screw (B) from the fixture and take down the mounting back plate.
- The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch in the canopy (Fig. 4).
- Secure the mounting ring (C) to the junction box using junction box screws.
- Connect the fixture wires and house wires as follows:
- Fixture Wires Black or Smooth to House Wires Black (Hot)
- Fixture Wires White or Ribbed to House Wires White (Neutral)
- Fixture Wires Bare wire (Ground) to House Wires Green or Bare Copper (Ground)
- Switch on the power and test the functionality of the installed fixture.
INSTALLATION INSTRUCTION
613-LED Wall Sconce WS-61326/WS-61334
- CAUTION: To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning.
- Read all instructions before installing.
- System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
- When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
- Retain installation instructions for future maintenance reference.
- WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
- Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.
- MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
HARDWARE
PREPARATION
- Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.
- Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
- MOUNT ON 2″X4″ SWITCH BOX (Fig. 1)****
-
Loosen the mounting screw (B) from the fixture, and remove the mounting back plate.
-
The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch in the canopy (Fig. 4).
-
Secure the mounting back plate to the switch box using junction box screws.
-
Using any other non-original-manufacturer provided junction box screw may result in safety issue;
-
The side of the mounting plate marked “GND” must face out
-
Secure the fixture to the mounting back plate using the mounting screw (B).
-
Connect the driver input wires to switch box wires as shown in Fig. 3, making sure that all wire connectors (A) are secured. If your
outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fxture’s ground wire
directly to the mounting back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch
box. Secure the fxture to the mounting back plate using the mounting screw (B). -
- MOUNT ON 4″X4″ JUNCTION BOX (Fig. 2)
- MOUNT ON 4″X4″ JUNCTION BOX (Fig. 2)
-
Remove the mounting screw (B) from the fixture, and then take down the mounting back plate.
-
The lamp can switch between three color temperatures (2700K-3000K-3500K),
which can be adjusted to your preference with the switch in the canopy (Fig. 4). -
Secure the mounting ring (C) to the junction box using junction box screws.
-
Using any other non-original-manufacturer provided junction box screw may result in safety issue;
-
The side of the mounting ring marked “GND” must face out
-
Secure the mounting back plate and conversion plate (D) to the mounting ring (C) with the junction box screws.
-
Connect the driver input wires to junction box wires as shown in Fig. 3, making sure that all wire connectors (A) are secured. If your outlet box has a green and bare copper ground wire, connect the txture’s ground wire to it. Otherwise, connect the fxture’ ground wire directly to mounting ring using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
-
Secure the fixture to the mounting back plate using the mounting screw (B).
- dweLED.com
- Phone (800) 526.2588
- Fax (800) 526.2585
- Headquarters/Eastern Distribution Center 44 Harbor Park Drive Port Washington, NY 11050 Central Distribution Center 1600 Distribution Ct Lithia Springs, GA 30122 Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
- WAC Lighting retains the right to modify the design of our products at any time as part of the company’s continuous improvement program. Nov. 2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>