WAC LIGHTING 1061-27SS Tyler 12 2.00 watt Stainless Steel Path Indicator Light Instructions
- June 9, 2024
- WAC LIGHTING
Table of Contents
INSTALLATION INSTRUCTION
Mini In-Ground
1011/ 1021/ 1031/ 1041/ 1051/ 1061/ 2011/ 2012/ 2021/ 2022/ 2031
2041/ 2051/ 2052/ 2061/ 2071/ 2081/ 2091/ 2101/ 2111/ 2121/ 2131
SAFETY INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting off the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
- Place the wall switch in the”OFF” position. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF”the circuit breaker switch(es) that control the power to the space that you are working on.
CAUTION: All parts must be used as indicated in these instructions. Do
not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction could invalidate the ETL/cETL
listing of this fixture.
THIS INSTRUCTIONS APPLY TO THE MODELS BELOW:
*Note: Transformer is required to power the fixture. (sold separately)
WAC Lighting retains the right to modify the design of our products at any time as part of the company’s continuous improvement program. JAN, 2022 1
SOFTSCAPE INSTALLATION
*Note: Transformer is required to power the fixture. (sold separately)
- Turn the main power off.
- Dig a hole at the point of application. Make sure the hole measures roughly 0A* in diameter and 4 inches in depth. (Fig.1)
- Place a layer of pea gravel at the base of the hole to help with drainage.
- Connect the fixture wires to landscape wires coming from the transformer using the outdoor rated direct burial wire nuts provided
- Place the fixture in the hole and repack the soil to hold it in place. Make sure the trim is flush with the ground.
For model #1011/1021/1031/1041/1051/1061: A =01 in.
For mode! # 2011/2012/2021/2022/2041/2051/ 2052/2061/2071/2081/2091/2101/
2111/2121/2131: A = 02 in.
HARDSCAPE INSTALLATION
*Note: Transformer is required to power the fixture. (sold separately)
- Turn the main power off.
- Prepare a hole large enough (B* diameter) to fit a schedule 80 pipe (not included). (Fig.2)
- Install the pipe into the hole
- Connect the fixture wires to low voltage wires coming from the transformer using the outdoor rated direct burial wire nuts provided.
- Smear some plumbers’ silicone (not included) on the 0-rings of the fixtures to help keep moisture out.
- Insert the fixture into the pipe, making sure the trim is flush with the mounting surface.
For mode! # 1021/1031/1041/1051/1061: B = 01.315 in.
For mode! # 2021/2022/2041/2051/2052/ 2061/2071/2081/2091/2101/
2111/2121/2131: 13 = 02.375 in.
OUTDOOR WALL INSTALLATION
*Note: Transformer is required to power the fixture. (sold separately) UL listed for outdoor use only
- Turn the main power off. 2. Attach the spring clip using the provided clip screws. 3. Cut a hole at the installation location. (Fig.3)
- Connect the fixture wires to low voltage wires coming from the transformer using the outdoor rated direct burial wire nuts provided.
- Smear some plumbers’ silicone (not included) on the 0-rings of the fixtures to help keep moisture out.
- Insert the fixture into the hole, making sure the trim is flush with the mounting surface
For model # 1021/1031/1041/1051/1061: C = Ø1.375 in.
For model # 2021/2022/2041/2051/2052 2061/2071/2091/2101/2111/ 2121/2131: C =
Ø2.25 in.
FOUNTAIN INSTALLATION
*Note: Transformer is required to power the fixture. (sold separately)
- Turn the main power off.
- Mount the fixture onto the assembled fountain canopy using the provided screws.
- Checking the required drill size for your flush mount plastic anchors for No. 6 screws, use a hammer drill with a masonry bit to drill out two holes at the screw locations. The depth of the hole should be slightly longer than the length of the plastic anchor.
- Place the flush mount plastic anchor (not included) in the hole, using the back of a screwdriver to gently hammer it in.
- Replace the fixture and rotate the fountain canopy until it is in the desired position. Make sure to line up the slots with the anchors.
- Screw the No. 6 screws into the plastic anchors, securing the fixture.
- Connect the fixtures wires to landscape wires connected to your transformer using the provided outdoor rated wire nuts.
- Loosen the thumbscrew and rotate the fixture so that it is facing the desired direction. Refasten the thumbscrew to secure.
Note: Only for model # 2031
CONCRETE POUR INSTALLATION
*Note: Transformer is required to power the fixture. (sold separately)
- Turn the main power off.
- Install wiring and conduit (use 1/2″ NPT) at desired position, plug all un-used holes. Refer to applicable wiring diagram. (Fig.5)
- Secure 4″ weatherproof junction box to the ground, preferably over a layer of sand or pea gravel for drainage.
- Cut Schedule 80 PVC Pipe in excess length for planned concrete thickness. (An 18″ long pipe is supplied with concrete pour kit) *Make sure the cut end is put into the concrete pour kit
- Insert the PVC pipe into the mounting flange and lock it with screws
- Secure concrete pour kit onto the 4″junction box.
- Pour desired amount of concrete, making sure NO CONCRETE ENTERS THE BOX. (Fig.6)
- After the concrete has cured, cut off excess PVC pipe protruding from the ground. (Fig.7)
- Connect fixture wires to box wires using the outdoor rated direct burial wire nuts. (Fig.8)
- Smear plumbers’ silicone (not included) to 0-rings.
- Insert LED Fixture into flange with a twisting motion. Make sure the trim is flush with the top of the poured concrete.
- To remove fixture, use a small flat head screwdriver and pry it from the flange. (Fig.9)
| 
---|---
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585| Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050| Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122| Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
---|---|---|---
WAC Lighting retains the right to modify the design of our products at any time as part of the company’s continuous improvement program. JAN, 2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>