SAL SWL10L Push Button Switch User Guide
- June 13, 2024
- SAL
Table of Contents
SAL SWL10L Push Button Switch
Product Information
| Model No. | SWL10L |
|---|---|
| Input (V)/(Hz) | 250/50 |
| Load rating | 10AX |
| IP | 20 |
| Color | White |
| Dimension L x W x H (mm) | 42 x 22 x 22 |
| Wireless | N/A |
Product Usage Instructions
Wiring and Installation
LED indicator permanently on Load off permanently, on momentarily Connect
the light fitting (Load) to the NEUTRAL and ACTIVE terminals. The LED
indicator will be permanently on, and the load will be off permanently but can
be turned on momentarily. LED indicator off permanently, on momentarily Load
off permanently, on momentarily Connect the light fitting (Load) to the
NEUTRAL and ACTIVE
terminals.
The LED indicator will be off permanently, and the load will be off permanently but can be turned on momentarily. LED indicator permanently on Load on permanently, off momentarily Connect the light fitting (Load) to the NEUTRAL and ACTIVE terminals. The LED indicator will be permanently on, and the load will be on permanently but can be turned off momentarily. LED indicator on permanently, off momentarily Load on permanently, off momentarily Connect the light fitting (Load) to the NEUTRAL and ACTIVE terminals. The LED indicator will be on permanently, and the load will be on permanently but can be turned off momentarily.
Warranty
In accordance with SAL’s standard terms and conditions of sale, SAL
warrants this product to be free from defects in materials and/or workmanship
for a specified period. This warranty does not cover incorrect installation,
maintenance, operation, mishandling, environmental factors, unauthorized
modifications, or electrical operating conditions outside the specified
product specification. You are entitled to a replacement or refund for a major
failure and compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major
failure.
To make a claim under warranty, contact SAL National Pty Ltd at the following addresses:
| State | Address |
|---|---|
| NSW | ACT |
| QLD | 36 Whitelaw Place Richlands QLD 4077 |
| VICT | TAS |
| WA | 29 Beringarra Av Malaga WA 6090 |
Foreword
IMPORTANT: IN THE INTEREST OF PRODUCT PERFORMANCE AND SAFETY PLEASE READ THESE GUIDE AND WARRANTY INSTRUCTIONS BEFORE INSTALLING THE PRODUCT
SAL products are designed in accordance with all mandatory International and Australian Standards, which require installation in accordance with AS/NZS3000 by a qualified installer and regular cleaning and maintenance of the equipment. Products are sold in accordance with the following instructions and SAL standard terms and conditions of sale, available via www.sal.net.auDue to continued product and information updates, product data sourced from sal.net.au shall not form part of any contract and or technical performance guarantee unless expressly confirmed in writing by SAL at the time of order. The product wireframe drawings in this document are intended for illustration purposes only and may differ from the final physical product. The installation instruction is subject to change without prior notice.
Product Introduction
SAL Push Button Switch is a mechanical push button ON/OFF switch, with different wiring options to enable/disable the LED indicator.
Product Features
- Fits most branded switchplates
- Fits 1 to 6 gang wall plate installation
- Same look as PIXIE smart switches under the PIXIE ambiance cover plate
- LED indicator can be enabled and disabled
- 10AX load rating
The package includes
- SAL Push Button Switch * 1
- Extra keycaps * 2
- Quick Start Guide * 1
Product illustration
All drawings shown are for illustration purposes only, the actual product may vary due to product enhancement.
Specifications
Wiring and Installation
LED indicator permanently on
Load off permanently, on momentarily
LED indicator off permanently
on momentarily Load off permanently, on momentarily
LED indicator permanently on Load on permanently, off momentarily
LED indicator on permanently, off momentarily Load on permanently, off
momentarily
Installation process
- Make sure the key cap compatibility, fits a suitable keycap
- Check and confirm the load compatibility
- Turn OFF the mains electricity supply before commencing installation
- Connect the switch according to the wiring diagram
- Turn ON the mains electricity supply, then test the switch operation by pressing the switch button.
Warranty
In accordance with SAL’s standard terms and conditions of sale, SAL warrants this product to be free from defects in materials and or workmanship for a period as stated below for goods not subject to incorrect installation, maintenance, operation, mishandling, environmental, unauthorized modifications or electrical operating conditions outside the nominated product specification as detailed in these installation instructions. The benefits to you given by this warranty are in addition to other rights and remedies you have under the law. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Warranty term – Residential usage (12) months, Commercial usage (12) months
How to make a claim?
Step #1 – Within 30 days of the fault discovery, please contact the
original place of the SAL product purchase during standard (local) business
hours, with the following information (a) proof of purchase (b) description
and quantity of the claimed fault (c) address of installation. (d) operating
hours of the product.
Step #2 – It is then the responsibility of the original place of product
purchase to report the matter to SAL aftersales;
Step #3 – Upon review of your claim and if the product is required to be
returned to SAL for technical evaluation, then at the owner’s expense the
product must be returned to SAL as per the above-nominated locations.
Step #4 – Pending the evaluation, the claim will be validated resulting
in the product being repaired or replaced with the same or best equivalent
product at the discretion of SAL, or rejected if the product fault was found
to be caused by conditions beyond the responsibility of SAL warranty
obligations. Consideration of installation, product removal, return freight,
and or testing fees are not the responsibility of SAL.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>