SSV Works MT-F65A Speakers User Manual
- June 12, 2024
- SSV WORKS
Table of Contents
SSV Works MT-F65A Speakers
Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle.
Introduction
SSV Works, an acclaimed USA-based manufacturer, has a rich legacy of producing top-notch audio equipment that caters to diverse sound preferences. The SSV Works MT-F65A speakers embody the brand’s commitment to delivering quality sound experiences in a sophisticated package. Specially designed to capitalize on unused space, these custom-molded kick panels are more than just speakers; they are a blend of art and technology.
Specifications
- Brand: SSV Works
- Model: SSV Works MT-F65A
- Item Weight: 11.75 pounds
- Product: Dimebnsions 16 x 10.5 x 10 inches
- Country of Origin: USA
- Item model number: MT-F65A
- Is Discontinued By Manufacturer: No
- Exterior: Painted
- Manufacturer Part Number: MT-F65A
What’s in the box
- SSV Works MT-F65A
Features
- Custom-molded Design : The MT-F65A isn’t a one-size-fits-all product. The kick panels are tailored for 6.5” speakers, promising optimized sound delivery.
- Strategic Placement : These kick panels bolt into the unused space above the footwell. By doing so, they remain conveniently out of the way, ensuring your feet have ample space and the sound is projected efficiently.
- 100% Fiberglass Construction : Fiberglass is renowned for its sound-enhancing properties. The MT-F65A’s fiberglass composition ensures unparalleled sound quality and impressive bass response.
- Aesthetic Finish : The black texture coat isn’t just about durability. It adds a touch of elegance, ensuring the speakers look as good as they sound.
- Stainless Mounting Hardware : The inclusion of stainless hardware underscores the product’s durability. Whether you’re traversing rough terrains or cruising smooth highways, these speakers remain firmly in place.
- User-friendly Installation : SSV Works believes in empowering its users. The inclusion of step-by-step instructions ensures even novices can set up their MT-F65A speakers with ease.
- Proudly Made in the USA : For those who value local craftsmanship, the MT-F65A speakers, originating from the USA, promise impeccable quality and reliability.
In a market flooded with generic audio solutions, the SSV Works MT-F65A speakers stand out. They aren’t just about sound; they are about an experience—an experience of quality, craftsmanship, and acoustic brilliance.
WARRANTY INFORMATION
All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All SSV Works Speakers are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.
TOOLS NEEDED FOR INSTALLATION
- T-30 Torx Driver
- 10mm Wrench
- Drill
- 1/4” & 1/8”Drill Bit
- Scribe
- Panel Removal Tool
PARTS LIST
Installation
- A. Install the enclosure brackets using two (2) M6 screws per bracket.
- B. Remove T30 torx screws and push pins securing the fender flare to the body of the machine.
- C. Put the pod in place and fasten the two (2) factory screws from the back side through the wheel well to secure the pod.
- D. While holding the pod in place, use a scribe to mark a drill point for the pilot hole.
- E. With the pod removed, use a 1/8” drill bit to drill a pilot hole. Then use a 1/4” drill bit for the mounting screw.
- F. Pull away the fender to gain access to install the hardware. Place the pod back in the mounting location and loosely mount the top side of the pod FIRST using the provided T30 torx screw, 10mm nut and washer.
- G. Fasten the two (2) factory screws from the back side through the wheel well to secure the pod. Then hand tighten all 3 (three) mounting screws to fully secure the pod.
- H. Route the speaker wire away from any moving parts and any sharp metal, then connect to the amplifier. Repeat installation on opposite side.
Connecting the MT-F65 using the pre-installed, four-pin connector will require an optional SSV Works plug-&-play harness (WP-H1151 – sold separately). If you are not using the WP-H1151 harness, simply cut off the four-pin connector and follow the wiring instruction below.
WIRING INSTRUCTIONS
For proper sound, ensure the speaker polarity is correct connect the “+” to the “+” and the “-“to the “-“from the speaker wire to the amplifier. If using with an SSV Works complete system refer to the amplifier wiring instructions for more detailed wiring information.
FAQs
What size of speakers are the MT-F65A kick panels designed for?
The MT-F65A kick panels are custom-molded specifically for 6.5” speakers.
Where are these speakers positioned in a vehicle?
The MT-F65A kick panels are designed to bolt into the dead space ABOVE the footwell, ensuring they are away from your feet and do not interfere with legroom.
What material is used in the construction of these speakers?
The kick panels are made of 100% fiberglass, ensuring the best sound quality and bass response.
What is the finish on the exterior of the speakers?
The MT-F65A speakers come with a black texture coat, providing both an aesthetic appeal and added durability.
Is there any mounting hardware included?
Yes, the package includes stainless mounting hardware to securely position the speakers.
I'm not very technically inclined. Is the installation process complicated?
Not at all! The MT-F65A speakers come with step-by-step installation instructions, making the setup process straightforward even for those unfamiliar with audio equipment installations.
Where are the MT-F65A speakers manufactured?
The speakers are proudly made in the USA.
Is the MT-F65A model still in production?
No, the MT-F65A model has not been discontinued by the manufacturer.
What's the weight and dimensions of the MT-F65A speakers?
The MT-F65A speakers weigh 11.75 pounds and have product dimensions of 16 x 10.5 x 10 inches.
Can these speakers be used outdoors or in marine environments?
While the MT-F65A speakers are designed with durability in mind, it's recommended to check with the manufacturer or retailer regarding specific use in marine or harsh outdoor environments.
How do the fiberglass panels influence the sound quality?
Fiberglass is known for its acoustic properties. It helps reduce unwanted resonance and enhances the clarity of the sound, ensuring rich bass and clear highs.
Do these kick panels come with the speakers installed or just the enclosures?
The product description emphasizes the kick panels' design and construction. You may need to purchase the 6.5
Download This PDF Link: SSV Works MT-F65A Speakers User Manual