i3 INTERNATIONAL B79T Angle Mount Camera Bracket for M79 User Manual
- June 12, 2024
- i3 INTERNATIONAL
Table of Contents
i3 INTERNATIONAL B79T Angle Mount Camera Bracket for M79
Product Information
The B79T Angle Mount Camera Bracket is designed for use with the M79 camera. It allows for flexible mounting options and provides a secure and stable base for the camera.
Package Contents:
- Round head screw, machine type x3
- Round head screw, tapping type with O-ring x4
- Plastic anchor x4
- Surface Mount template x1
Main Parts and Dimensions:
Dimensions:
- Diameter: 5 1/8″ (130 mm)
- Rubber gasket
- Cable retention clip RP1. 3/4 waterproof rubber plug
Installation Notes
Surface Installation:
- Use a security Torx bit or screwdriver to loosen the four screws securing the dome bubble to the M79 camera. Set the dome bubble aside.
- B79T comes with six 90% pre-drilled hole dimples. Depending on the type of installation and mounting surface, complete drilling 2-3 holes.
- Attach the mounting template to the mounting surface.
- Drill holes in the mounting surface, as marked on the template, to match the pre-drilled B79T holes.
- Insert anchors into the holes.
- Drill the conduit hole for the camera cable, as marked on the template.
- Secure the B79T back box to the mounting surface using the tapping screws with the O-ring. Tighten to fully compress the ‘O’ring.
- Pull the camera’s cable into the B79T back box.
- Use the round head machine screws to secure the camera base to the back box.
- Re-attach the dome bubble.
For a complete installation guide and additional information, please refer to the user manual provided in the QR code or visit ftp.i3international.com. If you have any questions or concerns regarding camera installation or require software services or support, please contact our Technical Support team at 1.877.877.7241 or support@i3international.com.
The B79T is an tilt angle mount back box for cable management and can be used
for
surface or horizontal wall mounting of i3’s M79 fisheye camera model.
- Tilt bracket for M79 Fisheye camera for best Panoramic view, ideal for wall mounting
- Back box for IP camera wire management.
- Suitable for outdoor and indoor installations.
- Six (6) pre-drilled hole dimples for surface mounting.
PACKAGE CONTENTS
In addition to this manual and B79T back box, the packing box includes:
- Round head screw, machine type x3
- Round head screw, tapping type with O-ring x4
- Plastic anchor x4
- Surface Mount template x1
Figure A. Accessories
DIMENSIONS
INSTALLATION NOTES
- Ensure that the mounting surface and mounting hardware is suitable for the chosen installation method.
- To maintain IP67 waterproof rating, always use the waterproof RJ45 connector supplied with the camera.
- Always add sealant to all threads in outdoor installations.
- Use a network cable 5mm or more in diameter to create a good seal in RP1.
- Tighten the provided tapping screws to fully compress the ‘O’ ring.
SURFACE INSTALLATION
Use the security Torx bit or screwdriver (not provided) to loosen four screws securing the dome bubble to the M79 camera. Set the dome bubble aside.
-
B79T comes with six 90% pre-drilled hole dimples. Depending on the type of installation and mounting surface, complete drilling 2-3 holes.
-
Attach the mounting template (4) to the mounting surface.
-
Drill holes in the mounting surface, as marked on the template, to match the pre-drilled B79T holes.
-
Insert anchors (3) into the holes.
-
Drill the conduit hole for the camera cable, as marked on the template.
-
Secure the B79T back box to the mounting surface using the tapping screws with the O-ring (2).
Tighten to fully compress the ‘O’ ring. -
Pull the camera’s cable into the B79T back box.
-
Use the round head machine screws (1) to secure the camera base to the back box.
-
Re-attach the dome bubble.
Figure C. Attaching B79T to the mounting surface.
- Attach the mounting template to the mounting surface.
- Drill holes in the mounting surface to match the holes in B79T.
- Insert plastic anchors into the holes in the mounting surface.
- Drill the conduit hole for the camera cable.
- Secure B79T to the mounting surface using the tapping screws with the O-ring. Tighten to fully compress the ‘O’ ring.
Figure D. Attaching M79 to B79T
- Pull the camera’s cable into the B79T.
- Secure M79T to B79T using the round head machine screws.
Figure E. Attaching M79 dome bubble
-
Re-attach the dome bubble.
Figure F. Complete Installation
-
Scan this QR code or visit ftp.i3international.com to view i3 product manuals.
-
Contact our Technical Support team at: 1.877.877.7241 or support@i3international.com if you have any questions or concerns regarding camera installation or if you require software services or support.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>