i3 INTERNATIONAL B88 Back Box Mounting Base User Manual

: June 3, 2024
: i3 INTERNATIONAL

Table of Contents

B88 Back Box Mounting Base
DIMENSIONS
**** INSTALLATION NOTES
WATERPROOF RJ45 CONNECTOR
Documents / Resources

Back Box Mounting Base

User Manual
B88

B88 Back Box Mounting Base

The B88 is an extension back box for cable management and can be used for surface, the pendant or horizontal wall mounting of i3’s Ax88 12MP Fisheye camera.

Back box for IP camera wire management.
Suitable for outdoor and indoor installations.
Six (6) pre-drilled hole dimples for surface mounting. Optional use with Pendant Mount EMT Pipe 3/4” or DB60 Horizontal Wallmount bracket.

PACKAGE CONTENTS
In addition to this manual and B88 back box, the packing box includes:

Round head screw, machine type x4
Round head screw, tapping type with O-ring x3
Plastic anchor x3
Surface Mount template x1

DIMENSIONS

i3 INTERNATIONAL B88 Back Box Mounting Base - Fig 1

**** INSTALLATION NOTES

In outdoor installations, remove RP1, add silicone to the DB60 Gooseneck bracket or EMT pipe threads (if using) and tighten the provided tapping screws to fully compress the ‘O’ ring.
Ensure that the mounting surface and mounting hardware is suitable for the chosen installation method.
To maintain IP67 waterproof rating, always use the waterproof RJ45 connector (Figure C).
Use sealant on all threads during installation.
Use a network cable 5mm or more in diameter to create a good seal in RP1 (if using).

INSTALLATION
Use the security Torx bit or screwdriver (not provided) to loosen three screws securing the dome cover to the Ax88 camera. Set the cover aside.

Surface Installation

B88 comes with six 90% pre-drilled hole dimples.
Depending on the type of installation and mounting surface, complete drilling 2-3 holes.
Attach the mounting template (4) to the mounting surface.
Drill holes, as marked on the template, to match the holes pre-drilled on the back box in Step 1.
Insert anchors (3) into the holes.
Drill the conduit hole for the camera cable, as marked on the template; pull the camera’s cable into the B88 back box.
Secure the B88 back box to the mounting surface using the screws with the O-ring (2). Tighten to fully compress the ‘O’ ring.
Use machine-type screws (1) to attach the Ax88 camera to the B88 back box.
Re-attach the dome cover.

DB60 / Pendant Installation (Follow Figure B)
Note: Do not drill any holes in B88.

Remove RP1 (rubber plug) from the B88.
Pull the camera’s cable through B88 opening and into the DB60 or the 3/4 EMT pipe.
Attach B88 to the DB60 or to the 3/4” EMT pipe (using a conduit fitting).
Add sealant as shown in Figure B
Use machine-type screws (1) to attach Ax88 camera to the B88 back box.
Re-attach the dome cover.

i3-TRNG-CAMS-B88.indd

i3 INTERNATIONAL B88 Back Box Mounting Base - Fig 2

WATERPROOF RJ45 CONNECTOR

i3 INTERNATIONAL B88 Back Box Mounting Base - Fig 3

Scan this QR code or visit ftp.i3international.com to view i3 product manuals.

Contact our Technical Support team at: 1.877.877.7241 or support@i3international.com if you have any questions or concerns regarding camera installation or if you require
software services or support.

QR Code for Complete
User Manual and ACT
http://ftp.i3international.com

Documents / Resources

| i3 INTERNATIONAL B88 Back Box Mounting Base [pdf] User Manual
B88 Back Box Mounting Base, B88, Back Box Mounting Base, Box Mounting Base, Mounting Base, Base
---|---