legrand ZLGP17 Wireless and Batteryless Lighting Control Instructions
- June 6, 2024
- Legrand
Table of Contents
legrand ZLGP17 Wireless and Batteryless Lighting Control
Wireless and batteryless lighting control 0 677 23L/73L/79L 0 770 53L – 6 000 83L 5 742 10/39/55 – 5 743 24 7 418 13L/43L/73L
INTRODUCTION
Requires to install the connected starter pack and one or more «… with
Netatmo» connected switch, micromodule, or socket outlet.
Pack contents
Start the configuration
Press the configuration button of Module Control or press the middle of the
wireless master switch until its light briefly turns green, and then stop
pressing. All wired products lights will turn green.
Pair the wireless, batteryless switch to control the connected products
(switch, micromodule, socket-outlet, latching relay)
Make sure that the indicator lights on the wired products are green and not
flashing. If not, go back to the precedent step. 1 .
- Tap 3 times the product to be controlled with the wireless, batteryless control. The light of the product to control flashes rapidly.
- For the specific case of the latching relay, press the main button of the latching relay until the configuration indicator flashes slowly in blue, release it then tap the wired product you want to control 3 times with the wireless, batteryless control. The indicator light of the product to be controlled flashes rapidly.
- While holding the “setup” button on the wireless, batteryless control, briefly press the “ON” or “OFF” button on the wireless batteryless control.
- The indicator light of the product to control will briefly turn blue and then will turn green again. The pairing was successful.
- Check the correct pairing by pressing the ON/OFF buttons
Multiple pairing: You can control several switches with the same wireless, batteryless switch by repeating the operation for each product that you want to control.
Complete the installation
To complete your installation, briefly press the configuration of the Module
Control or the middle of the wire-less Home / Away master switch.
All the indicator lights on the products switch off
If necessary, erase the configuration of the wireless batteryless control (factory reset)
While holding the “setup” button on the wireless, batteryless control, press
the upper button for 5 seconds. Confirm that your control is correctly reset
by making an ON command, then OFF
The undersigned, Legrand declares that the radio-electric equipment type (0
677 23L/73L/79L – 0 770 53L – 6 000 83L – 5 742 10/39/55 – 5 743 24 –
7 418 13L/43L/73L) complies with directive 2014/53/EU. The full text of the EU
declaration of conformity is available on the following website:
www.legrandoc.com
www.legrandoc.com/067723L
LEGRAND – Pro and Consumer Service – BP 30076 87002 LIMOGES CEDEX FRANCE •
www.legrand.com
FCC
This device contains license-exempt transmitter(s)/receiver(s) that comply
with FCC RF and Innovation, Science and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) This device must accept any
interference, including interference that may cause undesired operation of the
device.
This device complies with FCC and ISED radiation exposure limits set forth for
the general population. This device must not be co-located or operating in
conjunction with any other antenna or transmitter.
FCC Caution: the user that changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
FCC NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instruction, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Safety instructions
Make sure the power supply is disconnected before any intervention. Strictly
comply with instructions for installation and use.
References
- Welcome to Legrand - Legrand
- Legrand E-catalog International | Electrical Ranges of products & Connected Solutions
- legrandoc
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>