BEGA 12209.5 Wall Luminaire for Indoors Velvet Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 12209.5 Wall Luminaire for Indoors Velvet
Product Information
Product Name| Enclosed and free-radiating wall luminaire made of hand-blown
opal glass
---|---
Material| Metal housing with hand-blown opal glass
Usage| All lighting tasks in interior applications
Safety| The installation and operation of this luminaire are subject to
national safety regulations. Installation and commissioning may
only be carried out by a qualified electrician. The manufacturer
accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the
luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage Protection| The electronic components installed in the luminaire
are
protected against overvoltage in accordance with DIN EN 61547. To
achieve additional protection against transients, it is recommended
to use separate overvoltage protection components available on the
manufacturer’s website.
Product Usage Instructions
- Replacement of the LED module:
- The designation of the LED module is noted on a label in the luminaire.
- Disconnect the system and open the luminaire.
- Please follow the installation instructions for the LED module.
- The defective glass must be replaced.
- Close the luminaire.
Spares
| Ersatzteile | Part Numbers |
|---|---|
| Ersatzglas | 11 003 155 .1 |
| LED-Netzteil | DEV-0177/350 |
| LED-Modul 3000 K | LED-0589/930 |
| Blende | 72 000 862 M1 |
Wall luminaire for indoor use
Instructions for use
Application
Enclosed and free-radiating wall luminaire made of hand-blown opal glass, with
metal housing, for all lighting tasks in interior applications.
Product Description
- Metal luminaire housing, finish Colour velvet black
- Hand-blown opal glass
- Metal shield, finish color velvet black 2 mounting holes ø 4.5mm
- Distance apart 138mm
- 2 cable entries for through-wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@
- Connection terminal 2.5
- Earth conductor connection
- LED power supply unit
- 220-240 V y 50-60 Hz
- BEGA Thermal Switch
- Temporary thermal shutdown to protect
- temperature-sensitive components
- Safety class I
- r – Safety mark
- c – Conformity mark
- Weight: 1.1 kg
This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.
Lamp
- Module connected wattage 7.9 W
- Luminaire connected wattage 10 W
- Rated temperature ta=25 °C
- Ambient temperature ta max=25 °C 12 209.5K3
- Module designation LED-0589/930
- Color temperature 3000 K
- Color rendering index CRI > 90
- Module luminous flux 1040 lm
- Luminaire luminous flux 556 lm
- Luminaire luminous efficiency 55,6 lm/W
Installation
The luminaire must only be operated with the complete protective cover. LED
are high-quality electronic components! Please avoid touching the light output
opening of the LED directly during installation or relamping. Lead the main
supply cable through the cable entry into the luminaire housing. Fix the
mounting plate with enclosed or any other suitable fixing material onto the
mounting surface. Be sure to use the gasket rings supplied. Make an earth
conductor connection. Push silicone sleeves over the lines and make electrical
connections. Insert the glass into the luminaire housing and fix it by
screwing the shield hand-tight clockwise
onto the glass.
Cleaning · Maintenance
Clean the luminaire regularly with solvent-free cleansers from dirt. The defective glass must be replaced.
Replacement of the LED module
The designation of the LED module is noted on a label in the luminaire. The
light color and light output of BEGA replacement modules correspond to those
of the modules originally fitted. The module can be replaced by qualified
persons using standard tools. Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module. The defective
glass must be replaced. Close the luminaire.
Spares
- Spare glass 11 003 155 .1
- LED power supply unit DEV-0177/350
- LED module 3000 K LED-0589/930
- Shield 72 000 862M
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>