ZENEC ZE-RVC82MT Rear View Camera Instruction Manual
- June 13, 2024
- ZENEC
Table of Contents
**ZENEC ZE-RVC82MT Rear View Camera Instruction Manual
**
MOUNTING INSTRUCTIONS
KEY FEATURES
- Compact high resolution universal rear view camera
- Robust camera housing made of die-cast aluminum
- Cam sensor with 170° diagonal viewing angle for wide monitoring area behind the vehicle
- Vertical 140° image section adjustment by rotating sensor roller, 0° to 70° up / 0° to 70° down
- High sensitivity CMOS sensor with 0.3 lux light sensitivity for good night vision
- 10 m long separable system cable with mini 4-PIN connectors
- Required cable feed-through hole: 6.1 mm, easy mounting via M6 hollow thread screw
- IP69K certified
CAUTION
- Use the included connection cable exclusively. Modifying the cable will void your warranty.
- The camera is water- and dustproof and has been licensed according to the international standard IP69K. However, vehicle cleaning using high pressure water and steam jet devices may still lead to damage of IP69K rated camera models by intrusion of water.
- If the vehicle is treated with a water jet high pressure cleaning device, make sure to keep a distance of at least one meter between the water nozzle and the camera sensor / housing.
TECHNICAL SPECIFICATIONS
| Image device: | 6.09 mm SONY IMX225LQR CMOS sensor |
|---|---|
| Lens focal length: | f 1.8 |
| TV system: | NTSC / 30 fps |
| View angle: | 170° (D) x 135° (H) x 90° (V) |
| Native sensor resolution: | 1305 (H) x 977 (V) pixels |
| Resolution of video-out: | > 420 TV lines |
| Signal to noise ratio: | > 48 dB |
| Light sensitivity: | 0.3 Lux |
| Video output: | 1.0 Vp-p, 75 ohms CVBS |
| White balance: | Auto |
| Backlight compensation: | Auto |
| Gamma correction: | 0.45 |
| Gain control: | Auto |
| Sync system: | Auto |
| Power supply: | DC 6 -24 V |
| Current consumption: | 70 mA @12 VDC, 5 480 mW |
| IP protection rating: | IP69K |
| Operating temperature: | -30° C – +75°C, RH 95% max. |
| Dimensions (WxHxD): | 44 x 23 x 29 mm |
Rotatable Reverse Camera
Loosen the locking screw of the camera housing side cover.
Pull the camera cable out of the rectangular opening in the camera bottom. The
accessory set contains one piece of hollow thread screw, washer, M6 lock nut,
M6 spring washer, 3M adhesive pad and self-tapping fixing screw.
-
Camera housing
-
Side cover
-
3M adhesive pad
-
Hollow screw
Insert the cable into the groove from the hollow thread screw. Route the cable
with the hollow thread screw into the round hole in the camera base. Drill a
mounting / cable cable feed-through hole with a diameter of 6 mm. Fix the cam
via hollow threaded screw with washer, spring washer and M6 lock nut.
Alternatively, the camera can be fixed with the 3M adhesive pad or the self-
tapping screw. The cable must always be routed though the round hole in the
camera base to provide for full adjustment range of the sensor cylinder.
Loosely screw on the housing cover and align the camera. Tighten the locking
screw well.
UK
Declaration of Conformity
Hereby, ACR Brändli + Vögeli AG declares that ZENEC ZE-RVC82MT is CE
compliant – the EU Declaration of Conformity can be accessed via the following
Internet address: http://www.zenec.com (see link „Product Conformity
Documents“ in the footer area of the page)
E3: 10R-0616586
UK Authorised Representative
(for authorities only) ProductIP (UK) Ltd. 8, Northumberland Av.
London WC2N 5BY
ZENEC by ACR AG ∙ Bohrturmweg 1 ∙ CH-5330 Bad Zurzach ∙ Switzerland, EU
Legal
Representative: ACR S & V GmbH ∙
Industriestr. 35 ∙ D-79787 Lauchringen ∙ Germany Email:
www.zenec.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>