ZENEC ZE-RCE3804 Rear View Camera Instruction Manual
- June 3, 2024
- ZENEC
Table of Contents
MOUNTING INSTRUCTIONS
ZE-RCE3804
REARVIEW CAMERA FOR FORD TRANSIT
ZE-RCE3804 Rear View Camera
KEY FEATURES
- Compact, high-resolution plug & play reversing camera for replacement of the original 3rd OE brake light assembly, for commercial vehicles, vans, and minibusses based on the 7th generation FORD Transit incl. motorhomes, and camper vans
- Rugged injection molded red plastic main body with stainless steel clip-on mounting clamps
- ECE 148R certified brake light assembly (retaining the road homologation approval)
- Cam sensor with 140° diagonal viewing angle for wide surveillance of the area behind the vehicle
- Manually adjustable vertical image section of the camera sensor with +20° to -20° range to hit individually preferred field of view
- IR-LED lighting with 6 LEDs and dynamic brightness control via LDR element
- Integrated microphone for monitoring of environmental sounds via a control unit
- Separable 3-piece system cable of 10 m length with nut-secured 4-pin connectors
| Model | Type | Model Year |
|---|---|---|
| FORD Transit, all versions* | 7th Generation | 2014 − 2019 |
| FORD Transit, all versions* | 7th Generation, 2019 Facelift | as of 2019 |
*Commercial vehicles, vans, minibusses, and other versions based on 7th Gen vehicle hull structures such as motorhomes with swing-out rear doors and 3rd brake light at the rear top section.
TECHNICAL SPECIFICATIONS
| Image device Cam: | SHARP RJ2331 CCD sensor (with AA9050) |
|---|---|
| Image sensor type: | 1/3“ / 8.5 mm CMOS sensor |
| TV system: | NTSC / 30 fps |
| View angle: | 140° diagonal |
| Native sensor pixel matrix: | 976 (H) x 494 (V) |
| Image relevant resolution: | 700 TV lines |
| Lens focal length: | 2.6 mm |
| Frame rate: | 30 fields/sec., interlaced |
| Signal-to-noise ratio: | > 48 dB |
| Dynamic contrast: | > 60 dB |
| Light sensitivity: | 30 Lux with IR-LED ON |
| Video output: | 1.0 ±0.2 Vp-p, 75 , CVBS |
| White balance: | Auto |
| Backlight compensation: | Auto |
| Gamma correction: | 0.45 |
| Gain control: | Auto |
| Sync system: | Auto |
| Power supply: | 12 DCV |
| Current consumption (@12 V DC): IP protection rating: | : 80 mA ±10 mA |
| IP protection rating: | IP68 |
| Operating temperature: | -20° C ~ +70° C |
CAUTION:
- Use the included connection cable exclusively. Altering or replacing it will void your warranty.
- The camera is water- and dustproof and has been licensed according to the international standard IP68. However, vehicle cleaning using high-pressure water and steam jet devices may still lead to damage to IP68-rated camera models by water intrusion. Keep a distance of at least one meter between the water nozzle and the camera housing.
INSTALLATION:
The OE brake light insert can be unclipped from the vehicle. Access to the
stainless steel brackets to unlock the OE brake light is vehicle type
dependent. Two basic exist: the brake light insert is mounted directly on the
sheet metal body or else, it is fixed to the vehicle in a black plastic frame.
Vehicles with plastic frames allow unscrewing the frame/brake light assembly,
while Transit models with fully integrated brake lights must be accessed via
the vehicle interior. Remove the plastic covers in the roof area of the
vehicle to unlock the fixation clamps of the OE brake light with needle nose
pliers. Once the brake light is loose, unplug the power supply connector on
the backside.
For the OE brake light with plastic frame: Unclip the plastic frame from the
OE brake light and re-install it on the ZE-RCE3804 cam. Next, route the 10 m
extension cable from the dashboard to the mounting location of the camera.
Connect the A/V RCA connectors to the appropriate cam inputs of your head
unit, as indicated in the wiring diagram above. Then connect the red/black
power supply wires to the cam power outputs of your HU. Insert the power
supply connector on the backside of the ZE-RCE3804 cam housing. With all
wiring steps complete, insert the cam into the sheet metal recess and press
the cam into position until the stainless steel clips lock in place.
ZENEC by ACR AG ∙ Bohrturmweg 1 ∙ CH-5330 Bad Zurzach ∙ Switzerland
EU Legal Representative: ACR S & V GmbH ∙ Industriestrasse 35 ∙ D-79787
Lauchringen ∙ Germany ∙ www.zenec.com
148R00103-0293 10R-06101 16320
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>