ZENEC ZE-RCE3704-2S Rear View Camera Instruction Manual
- June 3, 2024
- ZENEC
Table of Contents
ZENEC ZE-RCE3704-2S Rear View Camera Instruction Manual
WIRING DIAGRAM
KEY FEATURES
- Compact high resolution rear view camera for FIAT Ducato III vehicles, incl. Series 8 and other identical type variants
- System design integrating the original Ducato brake light retaining the road use homologation*1
- Cam1 sensor with 50° and Cam2 sensor with 100° horizontal view angle
- Manual adjustment of vertical image section of Cam2
- IR-LED illumination system with dynamic LDR brightness control for Cam2
- Integrated microphone (Cam2)
- Separable main cable with DOMETIC CAM035 6-pin connectors, suitable for direct connection with factory routed DOMETIC main cable in vehicle
- Plastic injection main housing with stainless steel fi xation bolts *1
The ZE-RCE3704-2S integrates into the original brake light insert of the vehicle.
The brake light is not part of the supplied set content.
| COMPATIBLE WITH | MODEL TYPE | MODEL YEAR |
|---|---|---|
| Fiat Ducato III | 250/251 | 2006 – 2011 |
| Fiat Ducato III | 250/251 | 2011 – 2014 |
| Fiat Ducato III | 250/251 (X290) | 2014 – 2021 |
| Fiat Ducato III | Series 8 | as of 2021 |
| Citroën Jumper II | 250/250D/250L | as of 2006 |
| Peugeot Boxer | 250/251 | as of 2006 |
| Opel Movano | Type C | as of 2021 |
TECHNICAL SPECIFICATIONS
Image device Cam1 / Cam2: Pixelplus PC3089
Image sensor type: 1/3“ / 8.5 mm CMOS sensor
TV system: NTSC / 60 fps
View angle Cam1 / Cam2: 50° / 100° horizontal
Total sensor-die based pixel matrix: 756 (H) x 504 (V) pixels
Image relevant pixel matrix: 720 (H) x 480 (V) pixels
Lens focal length: f4.2 / f2.0
Frame rate: 60 fi elds/sec.
Signal to noise ratio: >47 dB
Dynamic contrast: >62 dB
Light sensitivity: 0.5 Lux/F1.2/50IRE – 0 Lux with IR-LED ON
Video output: 1.0 ±0.2 Vp-p, 75 Ω, CVBS
White balance: Auto
Backlight compensation: Auto
Gamma correction: 0.45
Gain control: Auto
Sync system: Auto
Power supply: 12 DCV (6 V – 16 V)
Current consumption (@12 V DC): 80 mA ±10 mA total for Cam1 + Cam2
IP protection rating: IP68
Operating temperature: -20° C ~ +70° C
CAUTION:
Use the included connection cable exclusively. Altering or replacing it will
void your warranty.
The camera is water- and dustproof and has been licensed according to the
international standard IP68. However, vehicle cleaning using high pressure
water and steam jet devices may still lead to damage of IP68 rated camera
models by water intrusion.
Keep a distance of at least one meter between the water nozzle and the camera
housing.
INSTALLATION
-
Unscrew and remove both Philips head screws.
Retain the screws for later remounting of the brake light reflector.
-
Pull the brake light reflector unit out of its mounting slot. Disconnect the white power supply system connector plug of the vehicle.
-
Screw in and tighten the stainless steel mounting bolts by hand (5Nm). Use a dab of Loctite, if possible.
-
Route the main cable from the naviceiver in the vehicle cockpit / dashboard to the brake light opening in the upper rear section of the vehicle. For power and RCA video signal, the ZENEC Infotainer offers a direct system “connector block E” which offers switched 300mA power out’s (see installation guide of ZENEC head unit).
-
Connect the 6PIN connector plug of the cam sensor side with its counterpart of the cable coming from the vehicle. Use self-adhesive tape to physically secure the connectors as well as to prevent water from entering the connectors.
-
Plug in the white power supply system connector plug in the socket of the brake light reflector housing backside.
-
Align the cam housing / reflector assembly over the mounting location. Fix the assembly with the original Philips head screws.
-
(no picture)
Connect the wires and connectors of the cam main harness to the HU in the dashboard. Perform a cam function test. Also check for proper function of the 3rd brake light.
-
Cam2 pointing down is a vertically swiveling design, allowing to align the desired image section shown on the HU manually. Align cam2 for best field of view. Installation and cam setup is completed.
ZENEC by ACR AG ∙ Bohrturmweg 1 ∙ CH-5330 Bad Zurzach ∙ Switzerland EU Legal
Representative: ACR S & V GmbH ∙ Industriestr. 35 ∙ D-79787 Lauchringen ∙
Germany
www.zenec.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>