BEGA 88913 Swimming Pool Luminaire Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
BEGA 88913 Swimming Pool Luminaire
Dimension
Application
Recessed swimming pool luminaire for the illumination of public and private swimming and bathing pools with drinking water supply.
- Pool with wall tiles
- Pool with film lining
- Metal or synthetic pool
Please note:
The luminaire is intended solely for use under water. Recommended installation depth 400 to 700 mm below the water surface.
The requirements set out in IEC 60364-7-702 (e.g. areas, ambient zones, etc.) are mandatory for the correct installation of the luminaire.
Direct or indirect contact with baser foreign metals via swimming pool water, tools, etc. must be prevented.
For water in swimming pools and bathing pools in accordance with DIN 19643 and typical pool water temperatures (max. 40 °C), the luminaire can be used in water with a chloride ion concentration of up to 500 mg/l.
The swimming pool luminaire is not suitable for brine pools, salt water pools or salt water electrolysis disinfection.
A 24 V safety direct voltage source with a smoothed residual ripple of max. 10 % is required for the operation of the luminaire – see accessories.
Important:
The luminaire must only be operated with a SELV operating device that meets the requirements of EN 61347-2-13. The maximum open-circuit voltage of 30 V DC must be SELV or SELV-equivalent. Alternatively, the connection may be made to safety transformers in compliance with EN 61558/VDE 0570 Parts 2-6 with an open circuit voltage of < 30 V DC. The transformer must be approved for this type of installation.
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Product description
Swimming pool luminaire made of stainless
steel – material no. 1.4404 – electropolished
Safety glass, clear
Silicone gasket
Reflector made of pure anodised aluminium 3m Connecting cable 05RN8-F 2×1❑
suitable for laying underwater Shell colour blue
Installation and luminaire housing with 1 screw cable gland each
Hose connection on installation housing for soft PVC protective hose ø 20 x
3mm
PVC protective hose for cable routing must be provided by the customer
BEGA article number 62000250
Safety class III
Protection class IP68 10m · Water pressure tight
Maximum submersion depth 10 m
Weight: 1.4 kg
This product contains light sources of energy efficiency class(es) D
Installation
Only stainless steel tools may be used for installation and maintenance work. The connection must be established on site with the correct protection class and safety class for the luminaire. The power supply unit may only be operated outside the water.
As maintenance work is carried out above the water level, make sure the cable is long enough.
Open the luminaire: Undo the screws and pull the luminaire housing out of the
recessed housing. Loosen the countersunk screws and remove the flange ring
from the recessed housing with both gaskets.
A safety direct voltage source with a 24 V smoothed residual ripple of max.
10% is required for the electrical connection of the luminaire – see
accessories.
If other safety direct voltage sources are used, an upstream fuse (max. 6 A)
must be provided by the customer
Terminal + : Cable wire red
Terminal – : Cable wire black
Installation in concrete pools:
The recessed housing is poured when constructing the pool.
Calibrate the recessed housing on the formwork and fix with countersunk
screws. Avoid contact with low-alloy or unalloyed steels.
Install the PVC protective hose provided by the customer, ø 20 x 3 mm (BEGA
article number 62000250) onto the recessed housing using the enclosed hose
clip until it is water-tight. Route the PVC house on-site in such a way that
the connecting cable can be inserted and the pool will not drain on its own.
If necessary, seal the PVC hose with an additional PG screw gland (BEGA
article number 750215V).
Concrete pools with tiled walls
After removing the formwork clean recessed housing, re-insert screws in order
to keep the tapped holes clean.
Tile the pool up to the inner diameter of the recessed housing.
Place the flange ring while using a flange gasket at the pool wall and connect
the complete unit firmly with the counter sunk screws.
The second flange gasket is only required for pools with foil lining and in
thin-walled pools.
If the screws are not long enough, use standard screws of sufficient length
made of stainless steel, 1.4401, 1.4404 or 1.4571.
Inject suitable compound between the flange ring and the recessed housing.
Lead cable through the screw gland and PVC hose.
Tighten the screw cable glands firmly and evenly.
Wind the cable evenly around the luminaire housing.
Insert the luminaire housing into the recessed housing and tighten the fixing
screws firmly and evenly
After removing the formwork clean the recessed housing. After inserting the
foil in the pool cut out the necessary opening and the holes for the screws.
The pool foil must be positioned between the two flange gaskets. Lead screws
through the holes of the flange ring, flange gasket – foil – second flange
ring. Bolt together the complete unit with the recessed housing. Tighten
counter sunk screws firmly. Lead cable through the screw gland and PVC hose.
Wind the cable evenly around the luminiare housing.
Insert the luminaire housing into the recessed housing and tighten fixing
screws firmly and evenly
Recessing in thin walled pools of metal or synthetic
Calibrate recessed opening with flange ring on the pool wall.
Flange ring can be used as a template for recessed opening ø 80 mm and through
boring ø 4.3 mm.
Cut out the recessed opening and the borings in the pool wall.
The pool wall must be positioned between the two flange gaskets.
Place the recessed housing from outside against the pool wall using the flange
gasket and place the flange ring from inside against the pool wall using the
second flange gasket.
Firmly bolt together the complete unit with the counter sunk screws.
Clamp the PVC hose ø 20 x 3 mm (BEGA 6200 0250) provided by others to the
recessed housing.
The PVC hose must be led in such a way that the connecting cable can be
inserted and that no self-emptying of the pool can occur.
Where appropriate seal the PVC hose with an additional PG gland (BEGA
750215V).
Lead the cable through the screw gland and the PVC hose.
Wind the cable evenly around the luminiare housing.
Insert the luminaire housing into the recessed housing and tighten fixing
screws firmly and evenly.
Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture
Lamp
Module connected wattage 3.6 W
Luminaire connected wattage 3.9 W
Rated temperature ta=25 °C
Ambient temperature ta max=60 °C
Voltage 24 V = DC
88 913K3
Module designation LED-1198/830
Colour temperature 3000 K
Colour rendering index CRI > 80
Module luminous flux 585 lm
Luminaire luminous flux 223 lm
Luminaire luminous efficiency 57,2 lm/W
Light technique
Installation depth 400 to 700 mm below water level.
In order to achieve uniform luminance
distribution for private swimming pools, we
recommend an axis distance of 2.00-3.00 m.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA
replacement modules correspond to those of the modules originally fitted.
The replacement must be carried out by a qualified person.
Disconnect the system from the power supply.
LED are high-quality electronic components!
Avoid direct skin contact with the
LED light aperture during replacements.
Undo screws at the luminaire housing.
Pull luminaire housing out of recessed housing, unwind cable and lift
luminaire housing over the pool edge.
Open the luminaire housing:
Undo hexagon socket head screws and lift the luminaire housing.
Undo screw at the LED-module and remove it.
Undo lamp wires at the connecting terminals.
Clean and dry the lamp housing, reflector, glass and gasket.
Please note the instructions under – cleaning · maintenance –
Check the gasket and replace, if necessary.
Note installation instructions of the LED module.
Fix replacement LED-module in the luminaire housing.
Retighten screw cable gland.
Insert reflector with glass and gasket into the luminaire housing. Replace
cover ring and tighten hexagon socket head screws firmly and evenly.
Wind the cable evenly around the luminaire housing.
Insert luminaire housing into the recessed housing and tighten fixing screws
firmly and evenly
Accessories
BEGA Safety transformers according to EN 61558-2-6/VDE 0570, part 2-6
70 564 Power supply unit for 5 – 15 W
70 465 Power supply unit for 10 – 25 W
70 565 Power supply unit for 20 – 35 W
70 566 Power supply unit for 30 – 50 W
70 567 Power supply unit for 40 – 75 W
70 169 Power supply unit for 70 – 150 W
70 223 Recessed distribution box for flush installation into floors or in walls. For the installation of cable for the swimming pool luminaire safety class III
For the accessories a separate instructions for use can be provided upon request.
Spares
Spare glass 14 000 378
LED module 3000K LED-1198/830
Reflector 76 001 233
Gasket flange 82 000 336
Gasket glass 83 001 829
Customers Support
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden ·
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>