Shenzhen Longzhiyuan Technology LY-138 Battery WiFi Camera User Guide

June 5, 2024
Shenzhen Longzhiyuan Technology

Shenzhen Longzhiyuan Technology LY-138 Battery WiFi Camera

Product Features

  1. 2×18650 batteries work regularly for 2~4 months
  2. FHD Megapixels collocated with wide-angle lens
  3. Support mobile phone remote fast wake-up within 6 second
  4. 2.4G Wi-Fi connection
  5. Support PIR motion detection, when someone hovers at the door, it will send push alerts to your mobile phone immediately
  6. With IR-cut, it can switch automatically and it is clearly visible at both day and night to keep your home and family safe
  7. Support to power by USB port

Product Specification Sheet

Lens FOV/130°Wide-angle lens (4Glass)
Infrared LEDs 10 pcs Infrared LEDs with 8 meters

ash distance

PIR Motion Sensor| 4~6 meters PIR distance
Storage| Up to 128GB Micro SD card
Connectivity| 802.11b/g/n Wi-Fi@2.4G
Power consumption| Standby 200uA Working 260mA
Battery| 2×18650 batteries
USB| DC5V
Wi-Fi distance| 60 meters (open space without obstacle)15 meters (indoor)
Video Compression| H.264
Voice Intercom| Two-way audio with noise cancellation
Video resolution| 1920*1080@15fps
Working Temperature| -10~ 55℃
Storage Temperature| -20~ 60℃

Product Design

  1. Lens
  2. Mic
  3. Light sensor
  4. LED
  5. Motion detection sensor
  6. Charge LED
  7. USB interface
  8. Speaker

Charge LED: Charging in Red; Full in GreenShenzhen Longzhiyuan Technology
LY-138 Battery WiFi Camera 1

  1. Reset button
  2. Mirco-SD card
  3. Power button
  4. 18650 Battery
  5. Flip Switch

Install your camera

Step 1: Please put the flip switch to “open” position and open the cover, then Install the 18650 battery and Mirco-SD.(Please notice the polarity of the battery). Press the Reset button long until you hear the “system reset” prompt from the camera speaker.

Note: Please notice the polarity of the battery. Please full charge this camera before using it for the erst time.

Step 2: Install anchors (on stucco, brick or concrete) On stucco, brick or concrete, use the bit to drill one holes in your wall, and install the anchors.install the base bracket on the wall

Step 3: Align the device to the base bracket and hold it, then adjust the appropriate angle, the installation is dehsin

Notes:

  1. USB interface is only used as power supply.
  2.  The mobile phone connects to the Wi-Fi of the home router, and the mobile APP can generate a QR code that made of router Wi-Fi name and password. The product recognizes the QR code through the lens on the product, and the product is automatically connected to the router and server after identification. At this time, the APP also and the product through the server, and the APP can control the operation of the product through the network.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirements. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals