BEGA 50913.4 Indoor Wall Luminaire Instruction Manual

June 13, 2024
BEGA

BEGA 50913.4 Indoor Wall Luminaire

BEGA-50913-4-Indoor-Wall-Luminaire-product-img

DIMENSIONS

BEGA-50913-4-Indoor-Wall-Luminaire-fig-1

Instructions for use

Application

  • Wall luminaire · Indoor luminaire with velvet black metal housing.
  • Luminaire with light source shielded to the front and metallic inside colour of the reflection surface.
  • Radial light emission 360°.

Product Description

  • Wall luminaire “STUDIO LINE”
  • Aluminium luminaire housing, finish Colour velvet black inside hue matt brass
  • Synthetic cover, translucent white 2 mounting holes ø 4.5 mm
  • Distance apart 190 mm 1 cable entry for through-wiring for mains cable
  • Connecting terminals 2.5@
  • Earth conductor terminal
  • 2-pole connection terminals for digital control
  • LED power supply unit 220-240 V 0/50-60 Hz
  • DC 196-250 V
  • DALI-controllable
  • Basic insulation is provided between the mains and control cables
  • BEGA Thermal Control®
  • Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
  • Safety class I
  •  – Conformity mark
  • Weight: 4.5 kg
  • This product contains light sources of energy efficiency classes D

Safety

  • The installation and operation of this luminaire are subject to national safety regulations.
  • Installation and commissioning may only be carried out by a qualified electrician.
  • The manufacturer accepts no liability for damage caused by improper use or installation.
  • If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

  • The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
  • To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
  • You can find them on our website at  www.bega.com.

Lamp

  • Module connected wattage 23.1 W
  • Luminaire connected wattage 25.8 W
  • Rated temperature ta = 25 °C
  • Ambient temperature ta max = 40 °C

50 913.4 K3

  • Module designation LED-1174/930
  • Colour temperature 3000 K
  • Colour rendering index CRI > 90
  • Module luminous flux 3655 lm
  • Luminaire luminous flux 699 lm
  • Luminaire luminous efficiency 27,1 lm / W

Installation

  • LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
  • Remove the mounting plate with LED unit from its packaging.
  • Loosen the knurled screw (slotted) and remove the ring made of synthetic material from the LED unit.
  • Pass the power connecting cable through the cable entry in the mounting plate.
  • Fasten the mounting plate with the supplied fastening material or other suitable fastening material to the installation surface.
  • Establish the earth conductor connection on the earthing screw ( ) of the mounting plate.
  • Make the electrical connection to the terminals.
  • Observe the correct configuration of the connecting cable. Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N).
  • The two connecting terminals marked DA, DA are provided for digital control purposes.
  • If these terminals are not assigned, the luminaire will work with full light output.
  • Insert the ring made of synthetic material back into the LED unit and tighten the knurled screw (slotted).
  • Unpack luminaire housing and carefully guide it over the LED unit.
  • Position and align the luminaire housing on the mounting plate and tighten the locking screw on the side.

Cleaning · Maintenance

  • Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

  • Replacing the power supply unit
  • The designation of the LED module is noted on a label in the luminaire.
  • The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The replacement can be carried out by a qualified person using standard tools.
  • Disconnect the system from the power supply.
  • Loosen the locking screw on the side and lift the luminaire housing off the mounting plate.
  • Loosen the knurled screw (slotted) and remove the ring made of synthetic material from the LED unit.
  • Disconnect the earth conductor connection and the electrical connection to the terminal.
  • Loosen the mounting screws of the power supply unit, the round blank bracket and earthing screws (Torx).
  • Remove the pot with LED module. Install the replacement pot.
  • Please follow the installation instructions for the LED module.
  • Replace defective LED power supply unit.
  • Install in reverse order.

Spares

  • Synthetic cover 15 000 650 B2
  • LED power supply unit DEV-0305/500i
  • LED module 3000 K LED-1174/930
  • Round blank Ø 500 71 003 452 B15
  • Round blank Ø 400 75 004 766

BEGA Gantenbrink-Leuchten KG

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals