CALIBER CAM 030 Reversing Camera User Manual
- May 15, 2024
- CALIBER
Table of Contents
CAM 030
MANUAL
SPECIFICATIONS
Power input: | DC 12Volts |
---|---|
IP rating | Water and weather resistant (IP68) |
Night vision | Yes |
Parking line | Yes |
Normal / mirror image
View angle| Horizontal angle 170°
Vertical angle 100°
set consists of:| Camera Ø 24mm (cable length 1m) Power cable (1,2m)
RCA Video extension cable (length 6m)
hole saw Ø 25mm)
brackets
screws
3x casing
Fastening sticker
For other languages please visit our website, search for CAM030 and check find
the manual under downloads
We are continuously improving/updating our products and product information.
It’s therefore possible that there is a slight difference between the
description in this manual to the operation of the product. If something is
different or not clear; always check our website for the most current version.
Warnings
The product is intended to assist in safe driving and to allow the driver
to have a broader rear view while the vehicle is in reverse. You, as the
driver, are solely responsible for the safe operation of your vehicle and the
safety of your passengers according to local traffic regulations. Do not use
any features of this system to the extent that it distracts you from safe
driving. Your first priority while driving should always be the safe operation
of your vehicle. Caliber Europe BV cannot accept any responsibility whatsoever
for accidents resulting from failure to observe these precautions or safety
instructions
- This product utilizes high voltage. Any unauthorized modifications or damage to the product may result in electrical shock. Handle all components with care. Inspect regularly for damage to components and cabling.
- You are responsible for ensuring that the installation of this product does not void or affect the vehicle manufacturer’s warranty. Caliber Europe or its subsidiaries are not liable in full or in part for improper installation resulting in loss or damage to your property, or for voiding all or part of the vehicle manufacturer’s warranty.
- Do not apply excessive force to any of the components contained within this kit. Excessive force used before, during or after installation that results in a damaged or non-functional part will void all warranties.
- Please follow the procedures in this installation manual. Improper installation or modification of this product will void all warranties.
Look for a location that will give you the best view behind the vehicle. This
should not be directly next to or under a reverse/backup lamp as it may blind
the camera at night. Avoid license plate lamps as well as they too can blind
the camera at night.
Determine which casing option (A/B/C) is most suitable for your vehicle.
Wire the camera’s power wire to the vehicle’s reverse lamp:
a) Locate the reverse lamp in the tail light assembly
b) Using a crimp connector or by soldering attach the red wire to the positive
12 volt wire from the reverse lamp. This should only have power when the car
is in reverse gear and the white lamp illuminated. Attach the black wire to
the Ground (Negative 12 Volts only).
Run the extension cable to the location of the monitor/head-unit (not
included) and connect the other end of the extension cable to the camera.
Yellow RCA connected to the Video/CAM input.
Blue wire:
Cut to turn off the guiding lines
White wire: Cut to horizontally mirror the image on screen
- Turn the camera OFF and ON again for the cut to take effect
Head-unit
On some head-units you need to connect the 12V red wire to the ‘back cam’ wire
on your head-unit. The screen will automatically turn ON when reversing.
| Option A) Built-in mounting Casing
Find a suitable location (depending on the type of vehicle in the
area at the rear, bumper).
Drill a hole with a diameter of 25mm (drill bit included) and insert the
camera.|
---|---|---
| Option B) Built-on mounting Casing
Find a suitable location (depending on the type of vehicle in
the area at the rear, above the number plate).|
| Option C) Built-on mounting Casing
Find a suitable location (depending on the type of vehicle in the
area at the rear, E.G above about the number plate).|
For all info on the disposal of items with the Wheelie bin icon, please see: webshop.caliber.nl/media/forms/wheeliebin.pdf
APPAREIL ET
EMBALLAGES A TRIER
Pour en savoir plus :
www.quefairedemesdechets.fr
WWW.CALIBEREUROPE.COM
CALIBER EUROPE BV : Kortakker 10 – 4264 AE Veen • The Netherlands
PRECAUTIONS
Caliber hereby declares that the item CAMO030 is in compliance with the essential requirements and other relevant provisions of Directive 2011/65/EU (RoHS), 2014/30/EU (EMC) and 2001/95/EC (GPSD).
**** Latest declaration form can be found at: www.calibereurope.com/nimedia/forms/DeclarationCAM030.pdf
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>