Fanvil i20S Indoor SIP Door Phone Installation Guide

SIP Door Phone
Quick Installation Guide

i20S
WWW.FANVIL.COM

Package Contents

 Physical Specifications

1.  Front Panel
   

and alert use.
MK| The door phone has a built-in microphone hidden in the pinhole located on the front panel.
RFID Reader| Use RFID cards to unlock the door by touching the RFID reader of the device.

Button Definition

LED Definition

| Steady Blue| Door unlocking
off| Door locking

| Blinks per second| Call Hold or Ringing
off| On-Hook
 Blinks every 3 seconds| The device in the issuing state
Steady Blue| Online talking

| Blinks per second| Network error
off| The network is normal, SIP is not registered
Blinks every 3 seconds| SIP Registration failed
Steady Blue| SIP Registration succeeded
2. Port Definition
After removing the Back Panel of i20S, there is one terminal block connector for power and lock control connection
as shown in the picture below.

Network Connector Power and Electric-lock Connect. –

JP1 Jumper
There are two modes for power supply of electric-lock as shown in the picture below.
(The default is “Passive Mode”).
Passive Mode: When the electric-lock starting current is more than 12V/500mA, need to use the external drive mode, the electric lock interface for short circuit output control.
Active Mode: When the electric-lock starting current is less than 12V/500mA, can use the internal drive mode, the electric lock interface is 12V DC output.

| |
---|---|---

Wiring instructions
NO: Normally Open Contact
COM: Common Contact
NC: Normally Close Contact

13](https://manuals.plus/wp-content/uploads/2021/11/Fanvil-i20S-Indoor-SIP- Door-Phone-figure-13.png)
√| | | √| |
| √| √| | |
| √| | √| |
| √| √| | |

Installation

Step 1: Installation preparation
A. Check the following contents:

• Hex wrench x 1
• RJ45 plugs x 2 (1 spare)
• KA4 x 25mm screws x 4
• 25mm screw anchors x4

B. Tools that may be required:

• Hex wrench
• Phillips screwdriver (Ph2 or Ph3), hammer, RJ45 crimper
• Electric impact drill with a 6mm drill bit

Step 2: Drilling

A. Place the mounting template with dimensions on the surface of a wall in a desired flat position.
B. Use an electric drill to drill the 4 holes marked on the mounting template. It is recommended to drill about 30mm deep. Remove the template when finishing drilling.
C. Push or hammer screw anchors into the drilled holes.

Step 3: Removing hanging shell
A. Remove the hanging shell in Figure 3 and Figure 4.

|
---|---

B. With Phillips screwdriver, unpacks the Back Panel and the main part of intercom as shown in Figure 5.

Step 4: Hanging shell Fixing and Cabling

A. Select the hole for cable supply; cable length of 15cm to 20cm is recommended.
B. With 4 KA4 x 25mm screws, tighten the Wall-mounted hanging shell as shown in Figure 6.

Step 5: Connection line

A. Select the hole for cable supply.
B. Connect the cables of RJ45, power, and electric lock to the motherboard socket as mentioned in the connector’s description (refer to Section 2).
C. Test whether there is electricity by doing the following:
Press the # button for 3 seconds to get the IP address of the intercom by voice.
Input access password or press the indoor switch to check the electric-lock installation.
Note: Do not proceed to mount until you have finished the electric checking.

Step 6: Mounting

A. Use the 4 screws to tighten the main part of the intercom on the back panel as shown in Figure 9.
B. Push the device into the Wall-mounted hanging shell and tighten it with 1 screw as shown in Figure 10.
C. Make sure the screws have been tightened properly for a better waterproof effect.

Searching Door Phone

There are two methods as shown below to search the i20S.
Method 1:
Open the door phone Network Scanner. Press the Refresh button to search the i20S and find the IP address.
(Download address http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe )

Method 2:
Press and hold the “#” key for 3 seconds and the door phone will report the IP address by voice.

Default Setting

Default DHCP Client| On
Static IP Address| 192.168.1.179
Default Web Port| 80
Default Login User Name| admin
Default Login Password| admin
Display IP address| Hold 4$ for 3 seconds to display by voice
Search Tools| iDoorPhone Network Scanner

SIP Door Phone Setting

Step 1: Log in to the homepage of the i20S.

Step 2: Add the SIP account.
Set SIP server address, port, user name, password, and SIP user with assigned SIP account parameters.
Select “Activate”, and then click Apply to save this setting.

Step 3: Setting DSS key
Set the DSS key as shown below for a quick start. Click “Apply” to save this setting.
Type: Hot Key
Number 1: The DSS Key will dial to this Number 1.
Number 2: If Number 1 is unavailable, it will be forwarded to Number 2.
Line: Working line
Subtype: Speed dial

Step 4: Door Phone Setting

Door Unlocking Setting

Local

1. Local Password
   Step 1: Go to EGS Setting → Features → Set Local Password (The default is “6789”).
   Step 2: Use the device’s Numeric Keyboard to input the password and “#” key, and then the door will be unlocked.
   

2. Private Access Code
   Step 1: Go to EGS Access → Access Rule → set Access Code.
   Step 2: Use the device’s Numeric Keyboard to input the password and “#” key, and then the door will be unlocked.

Remote
Remote Password
Step 1: Go to EGS Setting → Features → Set Remote Password (The default is “”).
Step 2: To answer the call made by the visitor via SIP phone, press the “” key to unlock the door for the visitor.

RFID Card
Step 1: Go to EGS Access → Enter the Name and ID Number (Only Front 10 yards) → Press Add to Access Table.
Step 2: Use pre-assigned RFID cards to unlock the door by touching the RFID area of the device.

References

• download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe
• Fanvil Technology Co., Ltd

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>