BEGA 31 042 Ceiling and Wall Luminaire Instructions

: June 13, 2024
: BEGA

Table of Contents

Dimensions
Application
Product description
Safety
Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 31 042 Ceiling and Wall Luminaire Instructions

Dimensions

Application

Ceiling and wall luminaire with an all-round shield made of copper and satin matt handblown opal glass for soft and uniform light distribution.

Some of the light exits behind the shield and also illuminates the mounting surface.

Product description

Luminaire back housing made of aluminium alloy BEGA Unidure® coating technology Surround made of copper Opal glass satin matt Silicone gasket 2 mounting holes ø 5.5mm
Distance apart 234mm 2 cable entries for through-wiring of mains supply cable ø 7-10.5mm, max. 5G1.5@ Connecting terminal 2.5@ with plug connection
Earth conductor connection BEGA Ultimate Driver® LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-276 V
DALI-controllable
Basic insulation is provided between the mains and control cables BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK03
Protection against mechanical impacts < 0.35 joule
Safety mark
Conformity mark
Weight: 3.1 kg

This product contains light sources of energy efficiency class(es) C

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability fordamage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp

Module connected wattage 13.8 W
Luminaire connected wattage 16.3 W
Rated temperature ta=25 °C
Ambient temperature ta max=50 °C

31 042K3

Module designation LED-0917/830
Colour temperature 3000 K
Colour rendering index CRI > 80
Module luminous flux 2585 lm
Luminaire luminous flux 1467 lm
Luminaire luminous efficiency 90 lm/W

Installation

Please use the protective gloves provided for the installation to prevent fingerprints on the luminaire.

Lead the mains supply cable through the cable
entry of the luminaire base.

Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.

Make the earth conductor connection and the electrical connection.

For digital control please use the connecting terminal DA, DA.

In case this terminal is not used the luminaire will be operated at full light output.

In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.

Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.

Push plug into coupler as far as it will go. Make sure that gasket is positioned correctly. Place the opal glass with LED unit onto the luminaire base in such a way that both yellow arrow markers align to each other and screw the glass clockwise into the base up to the stop.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system.

Turn the opal glass with the integrated LED unit to the left as far as it will go, and remove it. Disconnect the plug-in device.

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

To dismantle the LED unit, the two springs must be removed. To do this, use a small screwdriver to move the spring clip resting against the hexagon socket screw upwards and over the head of the screw (see drawing A).

The spring can then be removed.

Loosen the hexagon socket screws and take the LED unit out of the opal glass. Replace the LED modules.

Please follow the installation instructions for the LED module.

Insert the LED unit into the opal glass and secure it in place.

Then insert the springs at the two oppositehexagon socket screws. Make sure that the spring clip is properly located behind the heads of the screws (see drawing B).
Assembly Instruction

Push plug into coupler as far as it will go. Make sure that gasket is positioned correctly. Place the opal glass with LED unit onto the luminaire base in such a way that both yellow arrow markers align to each other and screw the glass clockwise into the base up to the stop.

Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits. Do not use high pressure cleaners.

Copper
The luminaire parts made of solid copper are delivered with the metal’s natural surface colour.

Time and weather factors create the natural patina characteristic for copper.

Spares