BEGA 50602.1 Wall Luminaire For Indoors Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
BEGA 50602.1 Wall Luminaire For Indoors
Dimension
Wall luminaire for indoor use
Application
Wall luminaire · indoor luminaire for brilliant light with crystal glasses and
aluminium luminaire housing.
The luminaire directs the light of the lamps upwards and downwards.
Product description
Luminaire made of Aluminium, finish Colour white
Crystal glasses, partially satin matt, with screw neck
Reflectors made of anodised pure aluminium
2 elongated fixing holes
Width 5 mm · 76,5 mm spacing
1 cable entry for mains supply cable up to
ø 10.5 mm max. 5 x 1.5@
Connecting terminal 2.5@
with plug connection
Earth conductor connection
2-pole connection terminals for digital control
LED power supply unit
220-240 V 0/50-60 Hz
DC 170-280 V
DALI-controllable
Basic insulation is provided between the mains and control cables
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Impact strength IK06
Protection against mechanical
impacts < 1 joule
– Safety mark
– Conformity mark
Weight: 3.0 kg
This product contains light sources of energy efficiency class(es) E
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Installation
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo set screw and lift off luminaire housing.
Loosen push plug connection and earth connection (plug connection).
Pass the power connecting cable through the cable entry in the mounting plate.
Note position of application of the mounting plate “arrow down”.
Fasten the mounting plate with the supplied fastening material or other
suitable fastening material to the installation surface. Make earth conductor
connection.
Push silicone sleeves over the lines and make electrical connection to
terminal (plug connection)
The two connecting terminals marked DA, DA are provided for digital control
purposes.
If these terminals are not assigned, the luminaire will work with full light
output.
Make earth conductor connection between luminaire housing and mounting plate.
Push plug into coupler as far as it will go.
Install luminaire housing over mounting plate and tighten set screw.
Note position of application of the luminaire “arrow down
Lamp
Module connected wattage 23 W
Luminaire connected wattage 26.3 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 25 °C
50 602.1 K3
Module designation 2x LED-0800/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 3470 lm
Luminaire luminous flux 2557 lm
Luminaire luminous efficiency 97,2 lm / W
50 602.1 K4
Module designation 2x LED-0800/940
Colour temperature 4000 K
Colour rendering index CRI > 90
Module luminous flux 3520 lm
Luminaire luminous flux 2593 lm
Luminaire luminous efficiency 98,6 lm / W
Replacement of the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA
replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Defective glass must be replaced. Close the luminaire.
Cleaning · Maintenance
Disconnect the electrical installation.
Unscrew glasses with reflectors from luminaire housing.
Remove reflector retaining springs.
Clean luminaire and glasses.
Defective glass must be replaced.
Use only solvent-free cleansers.
Attach reflectors with retaining springs to glasses.
Screw glasses with reflectors into luminaire housing.
Spares
Spare glass 11 003 448 10M RG
LED power supply unit DEV-0365/700
LED module 3000 K LED-0800/930
LED module 4000 K LED-0800/940
Reflector 76 001 796
Customer Support
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden ·
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>