BEGA 89758.2 Ceiling and Wall Luminaire Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
BEGA 89758.2 Ceiling and Wall Luminaire
Product Information
| Product Name | Unknown |
|---|---|
| Product Code | Unknown |
| IP Rating | IP44 |
| Luminaire Efficiency | 41% |
Detailed technical and lighting data for the lamps can be found in the data sheets on our website.
Product Usage Instructions
Safety:
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
The sliding-bolt closure:
The sliding-bolt closure provides a safe and vibration-resistant holding of
glass.
- Place glass to the base plate and observe that the holding springbolts fit into the notches of the glass.
- Turn the glass clockwise until it is locked. This ensures a safe and vibration-resistant holding of the glass.
- To release the glass from the base plate, turn it counter-clockwise.
Spares
Ersatzteile| Ersatzglas| LED-Leuchtmittel 2700 K| LED-Leuchtmittel 3000 K|
Fassung
---|---|---|---|---
Product Code| 11 002 770 .0R G| 13 548| 13 586| 63 000 187
Ceiling and wall luminaire for indoor use
DIMENSIONS
Instructions for use
Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass, satin matt and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required. Luminaire with a high protection class.
Lamp
-
Luminaire with screw base E 27
-
Lamp output max. 2 × 60 W
-
This product contains light sources of energy efficiency class E
Supplied lamp -
2 × BEGA LED lamp 13548
-
LED Retrofit 7 W · 805 lm · 2700 K dimmable
Supplied lamp -
2 × BEGA LED lamp 13586
-
LED Retrofit 7 W · 805 lm · 3000 K dimmable
-
Luminaire efficiency: 41%
Detailed technical and lighting data for the lamps can be found in the data sheets on our website.
Product Description
- Metal housing, finish Colour white aluminium Hand-blown opal glass, satin matt, with sliding-bolt closure
- 2 mounting holes ø 5.5 mm Distance apart 187,9 x 68,4 mm 2 cable entries for through-wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@ Connection terminal 2.5@
- Earth conductor connection Lampholder E 27
- Safety class I
- Protection class IP 44
- Protected against granular foreign bodies ≥ 1 mm and splash water
- Impact strength IK05 Protection against mechanical
- impacts < 0.7 joule
- Safety mark
- Conformity mark
- Weight: 3.0 kg
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to
the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Installation
- Pass the main supply cable through the mounting plate.
- Notice the position of the application »arrow down« when installed at the wall.
- Fix base of the luminaire with enclosed or any other suitable fixing material on to the mounting surface. It is imperative to use the enclosed gaskets.
- Make earth conductor connection. Push silicone sleeves over the lines and make an electrical connection. Insert lamp.
- Insert the opal glass into the luminaire base with sliding bolt glass closure and turn the glass clockwise up to the stop.
The sliding-bolt closure
- The sliding-bolt closure provides a safe and vibration-resistant holding of glass.
- Place glass to the base plate and observe that the holding spring bolts fit into the notches of the glass.
- Turn the glass clockwise until it is locked. Thus, you reach a safe and vibration-resistant holding of the glass.
- To release the glass from the base plate, turn it counterclockwise.
Relamping Maintenance
- Disconnect from main supply.
- Remove glass turning it counter-clockwise. Clean glass.
- Use only solvent-free cleansers.
- Change the lamp.
- Place glass into fitter and turn it clockwise until the stop.
Spares
- Spare glass : 11 002 770 .0R G
- LED lamp : 2700 K 13 548
- LED lamp : 3000 K 13 586
- Lampholder : 63 000 187
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>