BEGA 50269.1 Recessed Ceiling Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50269.1 Recessed Ceiling Luminaire
Product Information
- Lamp Module connected wattage: 21.4 W
- Luminaire connected wattage: 24.3 W
- Module designation: LED-0700/9TW
- Colour temperature: Adjustable from 2700 to 6500 K (Tunable White)
- Colour rendering index: 2R4a4>0
- Module luminous flux: 90 lm
- Luminaire luminous flux: 1702 lm
- Luminaire luminous efficiency: 70 lm/W
Dimension
Instructions for use
Application
Recessed ceiling luminaire · indoor luminaire with hand-blown crystal glass
and metal housing and external LED power supply unit. A focusing / dispersing
lens bundles the powerful LED light in the centre of the reflector for a
direct proportion of downlight. At the same time, a proportion of the
dispersed light is used to illuminate the luminaire glass and to generate the
vertical illuminance. Luminaire with adjustable colour temperature (Tunable
White). For installation into ceilings with a shallow depth in interior areas.
Product description
Recessed LED ceiling luminaire · Downlight with a remote DALI controllable
power supply unit Luminaire housing made of metal Ceiling trim ring made of
metal, Colour white Crystal glass with screw neck Additional focusing /
diffusing lens made of partially frosted crystal glass Reflector made of pure,
high-gloss anodized aluminium Silicone gasket Ceiling aperture ø 208 mm Free
space installation depth required 45 mm Fixing is achieved by using two
adjustable wedge-shaped claws 2-pole connecting terminal for digital control
BEGA Ultimate Driver® LED power supply unit 220-240 V x 0/50-60 Hz DC 176-264
V During DC operation the LED power is reduced to 50 % DALI controllable
(Device Type 8 for Tunable White according to IEC 62386-209) Number of DALI
addresses: 1 A basic isolation exists between power cable and control line
BEGA Thermal Control® Temporary thermal regulation to protect temperature-
sensitive components without switching off the luminaire Safety class II 2 r –
Safety mark c – Conformity mark Weight: 1.8 kg This product contains light
sources of energy efficiency class(es) E
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e. g. transients, etc. we recommend separate overvoltage
protection components. You can find them on our website at
www.bega.com.
- Lamp
- Module connected wattage 21.4 W
- Luminaire connected wattage 24.3 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 30 °C
- Module designation LED-0700/9TW
- Colour temperature adjust. 2700 – 6500 K
- Colour rendering index Ra > 90
- Module luminous flux 2440 lm
- Luminaire luminous flux 1702 lm
- Luminaire luminous efficiency 70 lm / W
Setting the colour temperature
The LED colour temperature of the luminaire can be set from 2700 to 6500 K
(“Tunable White”). Please note: To be able to set the LED colour temperature,
the controller used must support DALI Device Type 8. If no LED colour
temperature setting is made, 3000 K will be used by default.
Lighting technology
Half beam angle 46°
Installation
l Luminaire housing must not be installed in heat-insulating material. LED are
high-quality electronic components! Please avoid touching the light output
opening of the LED directly during installation or relamping. The recessed
opening is covered by the frame of the luminaire housing. Fixing of the
luminaire in the structure is achieved by using two adjustable wedge-shaped
claws.
Installation into concrete ceilings:
For this purpose installation housing 13 018 is available.
Installation into inserted ceilings:
A recessed opening of ø 208 mm is necessary to accept the luminaire housing.
Recessed depth min. 45 mm. The lateral distance between recessed luminaire and
other building parts must be at least 50 mm. The claws catch the ceiling
facing from the back side. Minimum thickness of the ceiling facing is 3 mm. If
the ceiling facing has a thickness of less than 10 mm or in case of an
installation into plasterboard ceilings, the facing thickness in the region of
the claws must be increased from the back side. Open luminaire: Remove glass
from luminaire housing by turning it counterclockwise. Open cover of the LED-
power supply unit and lead mains supply cable into it. Make electrical
connection to the terminals. For digital control please use the connecting
terminal DA, DA. In case this terminal is not used the luminaire will be
operated at full light output. Close cover of the LED-power supply unit. Push
external LED power supply unit and luminaire housing into the ceiling cut-out.
Luminaire housing and external LED
power supply unit must not be installed in heat-insulating material. Tighten
evenly screws of claw fasteners. Impress the enclosed cover ring about the
sealing ring onto the glass. Make sure that the sealing ring is seated
correctly! Slide enclosed – separately packed – dispersing lens into the
reflector. Screw glass with cover ring and dispersing lens into the luminaire
housing. Make sure that gasket is positioned correctly.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt. Defective
glass must be replaced.
Replacing the LED module.
The designation of the LED module is noted on a label in the luminaire. The
light colour and light output of BEGA replacement modules correspond to those
of the modules originally fitted. The module can be replaced by qualified
persons using standard tools. Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module. Inspect and,
if necessary, replace the luminaire gaskets. Defective glass must be replaced.
Close the luminaire.
Accessories
13 018 Installation housing For the accessories a separate instructions for
use can be provided upon request.
- Spares
- Dispersing lens 11 003 043 10R G
- Spare glass 11 003 049 42M 1RG
- LED power supply unit DEV-0264/700
- LED module LED-0700/9TW
- Trim ring 72 000 173 .2L
- Gasket glass 83 001 447
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>