BEGA 22 652 Ceiling and Wall Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
Technical amendments reserved
22 652
IP 65
Ceiling and wall luminaire
Instructions for use
Application
Luminaire with high constructive strength.
The thick-walled crystal glass with optical structure distributes the light
uniformly.
Product description
Luminaire made of aluminium alloy, aluminium and stainless steel BEGA Unidure
® coating technology
Crystal glass, white inside 2 mounting holes ø 5.5 mm
Distance apart 89 mm
2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm
Connecting terminal and earth conductor terminal 2.5@ BEGA Ultimate Driver ®
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-264 V
BEGA Thermal Switch ®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK07
Protection against mechanical
impacts < 2 joule
– Safety mark
**** – Conformity mark
Weight: 4.2 kg
This product contains light sources of energy efficiency classes C, D
Lamp
Module connected wattage| 6.6 W
Luminaire connected wattage| 7.7 W
Rated temperature| ta = 25 °C
Ambient temperature| ta max = 50 °C
22 652 K3
Module designation| LED-0262/930
Colour temperature| 3000 K
Colour rendering index| CRI > 90
Module luminous flux| 1115 lm
Luminaire luminous flux| 583 lm
Luminaire luminous efficiency| 75,7 lm / W
22 652 K4
Module designation| LED-0262/940
Colour temperature| 4000 K
Colour rendering index| CRI > 90
Module luminous flux| 1180 lm
Luminaire luminous flux| 617 lm
Luminaire luminous efficiency| 80,1 lm / W
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only becarried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components. You can find them on our
website at www.bega.com.
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Undo screws.
Remove luminaire top with glass and gasket.
Lead the mains supply cable through the cable entry of the luminaire base.
Fix luminaire base with enclosed or any other suitable fixing material onto
the mounting surface.
Be sure to use the gasket rings supplied.
Make the earth conductor connection and the electrical connection.
Insert glass with gasket and luminaire top.
Make sure that the gasket is in correct position.
Tighten screws firmly.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
Spare glass| 11 002 288 11
LED power supply unit| DEV-0304/350
LED module 3000 K| LED-0262/930
LED module 4000 K| LED-0262/940
Gasket| 83 000 547 .1
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden
· info@bega.com
· www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>