CONRAD 990-00126 LED Ball Worklight User Manual
- June 9, 2024
- CONRAD
Table of Contents
CONRAD 990-00126 LED Ball Worklight
OPERATING INSTRUCTIONS
SAFETY – EXPLANATION OF NOTES
Please take note of the following symbols and words used in the operating instructions, on the product and on the packaging:
- Information | Useful additional information about the product
- Note | The note warns you of possible damage of all kinds
- Caution | Attention – Hazard can lead to injuries
- Warning | Attention – Danger!
May result in serious injury or death
PROPER INTENDED USE
The product serves as a mobile light source and is not intended for use in other applications. The product is intended exclusively for private, household use and is not suitable for commercial use or for household room lighting and is only for use as described in the operating instructions. Use outside that stipulated in the information is improper use and this can result in damage to property or personal injury. We accept no liability for damage caused by incorrect or improper use.
GENERAL SAFETY INSTRUCTIONS
This product may be used by children from the age of 8 and by persons with
reduced physical, sensory or mental abilities or lack of experience and
knowledge, if they have been instructed on the safe use of the product and are
aware of the hazards. Children are not permitted to play with the product.
Children are not permit-ted to carry out cleaning or care without supervision.
Keep the product and the packaging away from children. This pro-duct is not a
toy. Children should be supervised in order to ensure that they do not play
with the product or packaging.
Avoid eye injuries – Never look directly into the beam of light or shine it
into other people‘s faces.
If this occurs for too long, the blue light portion of the beam can cause
retinal damage.
Never touch a device that is connected to the mains with wet hands, or if it
has fallen into water. In this case, first switch off the house circuit
breaker and then pull out the mains plug.
Do not expose to potentially ex-plosive environments where there are flammable
liquids, dusts or gases.
Never submerge the product in water or other liquids.
Use only an easily accessible mains socket so that the product can be quickly
disconnected from the mains in the event of a fault.
All illuminated objects must be at least 10cm away from the lamp.
Use the product exclusively with the accessories included with it.
DANGER OF FIRE AND EXPLOSION
Do not use while still in the packaging.
Do not cover the product – risk of fire.
Never expose the product to extreme conditions, such as extreme heat/cold etc.
Do not use in the rain or in damp areas.
GENERAL INFORMATION
- Do not throw or drop
- The LED cover cannot be replaced. If the cover is damaged, the product must be disposed of.
- The LED light source cannot be replaced. If the LED has reached the end of its service life, the complete lamp must be replaced.
- Do not open or modify the product! Repair work shall only be carried out by the manufacturer or by a service technician appointed by the manufacturer or by a similarly qualified person.
- Disconnect the device from the power supply only by pulling on the plug or plug housing, never on the cable.
- Information for the light and mains adapter as well as mains voltage on the socket must match with the type plate.
- The lamp shall not be placed face-down or allowed to topple face-down.
CLEANING | OPERATION
Before cleaning the light, disconnect the mains plug and allow the spotlight to cool down sufficiently. Clean with a dry or slightly damp, clean, lint-free cloth. Before each use, check the plug, mains cable and housing of the lamp for damage. If the lens is damaged, it must be replaced immediately. Clean any dirt from the housing or lens immediately as this may cause overheating.
ENVIRONMENTAL INFORMATION DISPOSAL
Dispose of packaging after sorting by material type. Cardboard and cardboard
to the waste paper, film to the recycling collection.
Dispose of the unusable product in accordance with legal provisions. The
„waste bin“ symbol indicates that, in the EU, it is not permitted to dispose
of elect-rical equipment in household waste.
For disposal, pass the product on to a specialist disposal point for old
equipment, use the return and collection systems in your area or contact the
dealer from whom you purchased the product.
Improper disposal may result in toxic ingredients being released into the
environment, which may have adverse health effects on humans, animals and
plants.
In this way you will fulfil your legal obligations and contribute to
environmental protection.
PRODUCT DESCRIPTION
- Carry handle
- Cable winder
- On/off switch
- Integrated socket with protective cover
- Base
- Mains plug
- Protective cover
- Integrated hanging hook
FIRST USE / OPERATION
Plug the mains plug in to a mains power outlet. The on/off switch is on the
side of the housing.
The lamp shall be set down only on stable and non-slip surfaces that are as
close to horizontal as possible. When placing it on slight inclines ensure
that the lamp
cannot topple over.
HOLDING DEVICES (HOOKS, STAND, ETC.)
If the light is the to be fastened with a holding device, ensure that the holding device is firmly/properly fastened in place. Observe max. mounting height! (Stand and fastening materials not included).
INTEGRATED SOCKETS
Do not connect devices with a combined power rating over 3000W (total output
power for the socket) to the integrated socket. IPX4 is only assured when an
IPX4 plug is connected to the device socket or the cover of the socket is
closed.
The product complies with the requirements from the EU directives.
Subject to technical changes. We assume no liability for printing errors.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>