BEGA 50 155.2 Recessed Wall Luminaire for Indoor Use Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

Application
Safety
Overvoltage protection
Installation
Cleaning · Maintenance
Replacement of the LED module
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Technical amendments reserved
50 155.2
Recessed wall luminaire for indoor use

Instructions for use

Application

Recessed wall luminaire · indoor luminaire with safety glass and metal housing.
Luminaire with shielded light for directing and conducting lighting.
Product description
Recessed ceiling luminaire »ACCENTA« Die-cast zinc luminaire housing Metal frame ring with safety glass, optical texture inside
Stainless steel finish
Reflector made of pure anodised aluminium Cavity-wall box with 2 fixing claws and fixing screws
Ceiling aperture ø 68 mm
Free space installation depth required 65 mm Mains cable up to ø 10.5 mm, max. 3 × 1.5@
Connecting terminal 1.5@
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-264 V
Safety class I
– Safety mark
– Conformity mark
Weight: 0.26 kg
This product contains light sources of energy efficiency classes D

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Lamp|
---|---
Module connected wattage| 1.9 W
Luminaire connected wattage| 3 W
Rated temperature| ta = 25 °C
Ambient temperature| ta max = 35 °C
50 155.2 K27

Installation

Luminaire housing must not be installed in heat-insulating material.
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Installation into solid walls
For this purpose a recess box, ø 68 mm and a recessed depth of min. 62 mm is necessary.
Installation into wall panels
A recessed opening of ø 68 mm is necessary to accept the cavity-wall box.
Recessed depth min. 65 mm.
The lateral distance between cavity-wall box and standard combustible building parts must be at least 40 mm.
The claws of the cavity-wall box catch the wall panel from the back side. If minimum thickness is less than 7 mm, it must be reinforced from the back side.
Maximum thickness of the panel must be no more than 35 mm.

Pass the mains cable through a cable entry of the recess box and fit the recess box.
Make sure that the countersunk screws of the recess box are horizontal relative to the ground.
Connect the earth conductor to the link on the luminaire housing.
Make electrical connection to the terminal of the power supply unit.
Insert the luminaire into the recess box and use the two countersunk screws to adjust and secure it.
Use retention pins to mount the trim ring with glass on the luminaire housing such that the two rear magnets are seated on the countersunk screws.
Note: This luminaire is supplied with a matching cavity-wall box.
If cavity-wall boxes of other manufacturers are used, they must be made of electrical insulating material such as plastic!
Through-wiring
Please note: Through wiring of the luminaire is only possible by means of an electronic box.
We recommend the use of a flush-mounted box Kaiser 1068-02 for flush-mounting and a cavity-wall box Kaiser 9268-94 for cavity wall mounting.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.
Defective glass must be replaced.

Replacement of the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Defective glass must be replaced.
Close the luminaire.

Spares|
---|---
Glass/Trim ring| 20 000 036 M1
LED power supply unit| DEV-0231/350
LED module 2700 K| LED-0676/927
LED module 3000 K| LED-0676/930
Reflector| 76001554

BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689
Menden · info@bega.com
· www.bega.com