RIGID D-Series D-SS Driving Surface Mount Instruction Manual

June 4, 2024
RIGID

RIGID logo

INSTALLATION INSTRUCTIONS
D-SERIES ® , D-SS  ™ & SR-Q SERIES ®
RIGID D Series D SS Driving Surface
Mount

THANK YOU FOR PURCHASING RIGID INDUSTRIES’ PRODUCTS FOR YOUR VEHICLE.
Please read through all of these Instructions and tips before proceeding with the installation. We do our best to provide a simple installation process for all applications however a professional installation is always recommended.
IMPORTANT Always disconnect any power sources connected to your vehicle before servicing fuses or electrical systems.

WIRING INSTRUCTIONS

STEP: 1 When routing a wire harness through any metal surface be sure it is free of any sharp edges and protected using wire sheathing or a grommet.
STEP: 2 Follow the WIRING DIAGRAM to ensure proper connection to switch and battery terminals.
STEP: 3 If connecting to existing wiring, make sure to use appropriate fusing and wire gauge. Be sure to use heat shrink tubing on all connections to ensure a weather-tight seal.
STEP: 4 Be aware of the current rating of your selected switch, if the switch rating is less than the amperage required to power your lighting then a relay must be added in line to prevent failure of the switch.
STEP: 5 Connect the positive and negative battery terminals once all connections have been made and test to verify functionality.
WIRING DIAGRAM FOR
RELAY HARNESS
NOTE: GOLD Spade is the Top of the SwitchRIGID D Series D SS Driving
Surface Mount - Switch

WIRING DIAGRAM FOR
NON-RELAY HARNESS
NOTE: GOLD Spade is the Topthe  of SwitchRIGID D Series D SS Driving
Surface Mount - Top of Switch

INSTALLATION INSTRUCTIONS

MOUNT INSTRUCTIONS & DIAGRAM FOR

D-SERIES & D-SS

  1. Place 5/16”- 18 Carriage Bolt (E) into Mounting Bracket (D).
  2. Use M6 Allen Socket Head (B) and M6 Nyloc Nut (C) to attach the Mounting Bracket (D) to Housing (A).
  3. Drill a 5/16” hole into desired mounting location.
  4.  Use 5/16”: Flat Washer (F), Lock Washer (G), and Nut (H) to secure the light assembly to the vehicle.
  5. Tighten all hardware.

A – LED Light (Housing)
B – M6 Allen Socket Head (2)
C – M6 Nyloc Nut (2)
D – Mounting Bracket
E – 5/16”- 18 Carriage Bolt
F – 5/16” Carriage Washer
G – 5/16” Carriage Lock Washer
H – 5/16”- 18 Carriage Nut

SR-Q SERIES

  1. Place 5/16”- 18 Carriage Bolt (E) into Mounting Bracket (D).
  2. Use 1/4“- 20 Allen Socket Head (B) and 1/4”- 20 Nyloc Nut (C) to attach the Mounting Bracket (D) to Housing (A).
  3. Drill a 5/16” hole into desired mounting location.
  4. Use 5/16”: Flat Washer (F), Lock Washer (G), and Nut (H) to secure the light assembly to the vehicle.
  5. Tighten all hardware.

A – LED Light (Housing)
B – 1/4” – 20 Allen Socket Head
C – 1/4“ – 20 Nyloc Nut
D – Mounting Bracket
E – 5/16”- 18 Carriage Bolt
F – 5/16” Carriage Washer
G – 5/16” Carriage Lock Washer
H – 5/16”- 18 Carriage Nut

Your installation is now complete.
Welcome to the Rigid Nation!
WARRANTY INFORMATION
For warranty information, visit www.rigidindustries.com/about/warranty 779 N Colorado St, Gilbert, AZ 85233 • 855-760-5337
www.rigidindustries.com
RIGID, SR-Q Series, D-Series, and D-SS and Rigid Industries are registered and/or common law marks owned by JST
Performance, LLC, a Delaware limited liability company d/b/a Rigid Industries.
IS-D-SRQ-E

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals