RIGID 2020+ Ford Super Duty A-Pillar Mount Kit Instruction Manual
- June 13, 2024
- RIGID
Table of Contents
RIGID 2020+ Ford Super Duty A-Pillar Mount Kit
Product Information
The 2020+ Ford Super Duty A-Pillar Mount Kit is designed to securely mount lights on the A-Pillar of your vehicle. The kit includes a driver-side bracket and a passenger-side bracket. Please note that lights are sold separately.
Recommended Tools
- 10mm socket
- 13mm socket
It is important to read through all the instructions and tips provided before
proceeding with the installation.
While we strive to make the installation process simple, we recommend
professional installation for optimal results.
Before servicing fuses or electrical systems, always disconnect any power
sources connected to your vehicle.
Product Usage Instructions
-
Step 1:
-
Open the vehicle’s hood and locate the hood hinges. Use a 13mm socket to remove two factory bolts.
-
Step 2:
-
Install the bracket brace onto the main bracket using the supplied M6 bolt and M6 U-Nut. Do not fully tighten at this stage.
-
Step 3:
-
Move the plastic cowl out of the way by removing the windshield wiper, and antenna, and disengaging the plastic clips holding the cowl in place. Use the lever at the base of the wiper to remove the windshield wipers.
-
Step 4:
-
Align the bolt holes and install the bracket onto the vehicle.
Re-install the factory bolts but do not fully tighten them. -
Step 5:
-
Using a 13mm socket, remove the factory bolt under the plastic cowl. Install the secondary support bracket and re-install the factory bolt. Use the supplied M8 carriage bolt, washer, and lock nut to secure the support bracket to the main assembly. Do not fully tighten.
-
Step 6:
-
Tighten all hardware and repeat steps 1-5 on the opposite side of the vehicle.
-
Step 7:
-
Re-install the cowl, antenna, and windshield wipers. Install the assembled light on the bracket and connect the wiring according to the instructions provided with the light.
-
Your installation is now complete. Welcome to the Rigid Nation!
Warranty Information
- RIGID and Rigid Industries are registered and/or common law marks owned by JST Performance, LLC, a Delaware limited liability company d/b/a Rigid Industries. For warranty information, please refer to your product documentation or contact Rigid Industries.
INSTALLATION INSTRUCTIONS
PRODUCTS INCLUDE:
- (1) Driver Side Bracket
- (1) Passenger Side Bracket
- Lights are sold separately.
RECOMMENDED TOOLS:
- 10mm socket
- 13mm socket
IMPORTANT
- THANK YOU FOR PURCHASING RIGID INDUSTRIES PRODUCTS FOR YOUR VEHICLE.
- Please read through all of these Instructions and tips before proceeding with the installation.
- We do our best to provide a simple installation process for all applications however a professional installation is always recommended.
- Always disconnect any power sources connected to your vehicle before servicing fuses or electrical systems.
STEP: 1
- Open the vehicle’s hood and locate the hood hinges, and remove two factory bolts using a 13mm socket.
STEP: 2
- Install bracket brace onto the main bracket using supplied M6 bolt and M6 U-Nut.
- Do not fully tighten.
- STEP: 3
- Move the plastic cowl out of the way by removing the windshield wiper, and antenna, and disengaging the plastic clips holding the cowl in place. Remove windshield wipers using the lever at the base of the wiper.
STEP: 4
- Install bracket onto a vehicle by aligning the bolt holes and re-install factory bolts. Do not fully tighten
STEP: 5
- Remove the factory bolt under the plastic cowl using a 13mm socket. Install the secondary support bracket and re-install the factory bolt. Install supplied M8 carriage bolt, washer, and lock nut to secure the support bracket to the main assembly. Do not fully tighten.
STEP: 6
- Tighten all hardware and repeat steps 1-5 on the opposite side of the vehicle.
STEP: 7
- Re-install the cowl, antenna, and windshield wipers. Install assembled light on the bracket and install wiring per the instructions supplied with the light.
- Your installation is now complete.
- Welcome to the Rigid Nation!
WARRANTY INFORMATION
- For warranty information, visit www.rigidindustries.com/about/warranty 779 N Colorado St, Gilbert, AZ 85233
- 855-760-5337 www.rigidindustries.com
- RIGID and Rigid Industries are registered and/or common law marks owned by JST Performance, LLC, a Delaware limited liability company d/b/a Rigid Industries. 11-14190-A
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>