Artis XTBD-22763 Wall Mounted Mirror Cabinet Instruction Manual
- May 15, 2024
- artis
Table of Contents
- Wall Mounted Mirror Cabinet
- Packing List
- Required tool
- Note: Please carefully read the following before installing
- The use of a spirit level
- Fixing the bar
- Positioning and Installation of Mirror Cabinet:
- Mirror Door Adjustment
- Loosen the snap screw (d) of the shelf to adjust the shelf position.
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Artis XTBD-22763 Wall Mounted Mirror Cabinet Instruction Manual
Wall Mounted Mirror Cabinet
- Adjustable stainless steel buffer hinge
- Double layer adjustable tempered glass shelf Touch sensor switch
- Aluminum alloy cabinet
- Double-sided copper-free silver mirror
Packing List
Expansion plug 08
Screw M5
L shape fixing
Aluminum alloy bar
Screw M4
Required tool
Tape measure| | Spirit level|
---|---|---|---
Spirit level| | Screwdriver|
Hammer| | Drill bit|
Pencil| | |
Note: Please carefully read the following before installing
warning
- Before installing the product, please carefully read the instructions and operate accordingly;
- Before installing, please turn off the main power switch and ensure that it won’t turn on;
- All electrical products should be fitted by a suitably qualified electrician in accordance with wiring regulations (BS7671)
- This mirror cabinet is heavy; do not lift or install with single person in order to avoid injury;
- Before installing, please check whether the product is broken, to avoid injury caused by damaged glass;
- Do not clean the product surface with acid and alkaline cleaning agent; please use a damp cloth.
The use of a spirit level
Non-standard level
-
standard level 1 Look at the bubbles in the glass tube in the middle of the spirit level. The bubbles stay in the middle of the two black lines. It’s horizontal.
-
Draw a straight line under the spirit level.
-
Place the Aluminum alloy bar on the drawn line, line up the hole position and punch the hole.
Installation Steps:
Fixing the bar
1.10pen the product packaging, and check whether the product has any exception
or functional damage; if yes, please return it to the dealer.
After selecting the location of the mirror cabinet, check whether the wall is
solid, measure the distance of the holes (A, A-1) in the aluminum alloy bar
with a tape measure and mark it on the wall with a pencil (Fig. 1).
Drill holes in the marked position with electric drill and ø8 drill bit, and
use special ceramic drill if the wall surface is ceramic tile.
Knock the expansion plugs into the holes in the wall with a hammer, and then
tighten the screws with a screwdriver to fix the bar, and calibrate the level
with a spirit level (Fig. 2).
Positioning and Installation of Mirror Cabinet:
Using a screw to tighten the L shape fixing on the bottom of the cabinet
(Fig.3).
Attach the mirror cabinet to the bar as shown in Fig. 3, open the cabinet
door, and mark on the wall with a pencil (Fig. 4) through the backplane
hole (a).
Remove the mirror cabinet, drill the fixing hole in the wall in the marked
position, and place the expansion plugs (Fig. 5).
Repeat the operation as shown in Fig. 3 and mount the mirror cabinet to
the bar, make sure that the circuit on the wall is not energized and connect
the three-core wire reserved on the wall to the three-core wire terminal block
on the product (Fig. 6),
and then tighten the screws on the backplane (Fig.6-b).
Finally, switch on the power, and then touch the switch sign (Fig. 7 )
with a finger on the lens to test the products
Mirror Door Adjustment
Fix the mirror cabinet, and check if the mirror door is flat; if not (as shown
in Fig.8) ,
adjust the distance of the door opening by adjusting the hinge screw (b)
and keep the door level (Fig.9)
Rotate CW: Door moves to the center of the mirror cabinet
Rotate CCW: Door moves to both sides of the mirror cabinet
If the cabinet door isn’t flat ( Fig. 10),
adjust the distance between the door and the cabinet by adjusting the screw
(c) to make the door flat. (Fig.11)
Warning: The distance between the door and the cabinet should not be too
small, otherwise the door can’t be opened and may lead to the door rupture.
Rotate CW: Distance between door and cabinet reduces
Rotate CCW : Distance between door and cabinet increase
Loosen the snap screw (d) of the shelf to adjust the shelf position.
(Fig.12
Safety Warning
- Do not disassemble the door unless necessary
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>