RIGID 202053 Radiance-Scene Fog Amber LED Fog Light Kit Instruction Manual
- June 12, 2024
- RIGID
Table of Contents
RIGID 202053 Radiance-Scene Fog Amber LED Fog Light Kit
Product Information
- The RADIANCE+ RGBW Series is a set of lights manufactured by Rigid Industries. These lights are designed for use in vehicles and provide a variety of backlight color options. The lights operate within a voltage range of 9V-16V and should not be used on systems with 24V or higher voltage as it may cause permanent damage to the electrical components. The Radiance+ RGBW lights are intended for off-road use only.
- The lights also feature a syncing function, which allows lights wired on the same circuit to sync together when the color selection switch logic is initiated.
Product Usage Instructions
Before proceeding with the installation, please read through the following instructions and tips. It is recommended to have a professional installation, although the installation process is designed to be simple.
-
Important Safety Precautions
- Always disconnect any power sources connected to your vehicle before servicing fuses or electrical systems.
- Always disconnect the negative battery terminal when working with any electrical circuits.
-
Mounting Installation:
- Insert the mounting brackets onto the light as shown in the provided diagram.
- Secure the hardware to a snug position.
- Mount the light in the desired location.
-
Functionality:
The Radiance+ RGBW lights utilize switch logic to change backlight colors. Follow the steps below to choose from one of the 8 available backlight color options:- Switch the backlight on-off-on-off within less than 1 second
- Continue switching off and on until the desired color is selected.
- Once the desired color is selected, keep the backlight on for more than 1 second to save the color.
- The backlight color is locked in until the process is repeated.
Note: If multiple Radiance+ RGBW lights are wired on the same circuit, they will sync together when the color selection switch logic is initiated.
-
Wiring Harness Installation:
- Always disconnect the negative battery terminal before working with any electrical circuits.
- When routing wires through any metal or abrasive surfaces, ensure that the surface is free of any sharp edges.
- Match the light pigtail to the harness colors: Red to Red (Forward projecting LED +12v trigger), White to White (back-lighting LED +12v trigger), and Black to Black (shared ground) using butt connectors.
- Find a desired location for switches and drill a 3/4″ hole for each switch.
- Connect leads from the wire harness to the switch using the provided diagrams.
- Route the main power and ground leads from the harness to the battery terminals and attach the RED lead to battery +12v and the BLACK lead directly to the battery ground.
- Re-connect the negative battery terminal and test switches to verify functionality.
Your installation is now complete. Welcome to the Rigid Nation!
THANK YOU FOR PURCHASING RIGID INDUSTRIES’ PRODUCTS FOR YOUR VEHICLE.
Please read through all of these Instructions and tips before proceeding with
the installation.
We do our best to provide a simple installation process for all applications,
however a professional installation is always recommended.
IMPORTANT
Always disconnect any power sources connected to your vehicle before servicing
fuses or electrical systems.
NOTE:
- Radiance lights are designed to operate from 9V-16V only. Using this product on a 24V or higher system will cause permanent damage to electrical components.
- Backlighting and forward projecting LED’s are intended for off-road use only.
FUNCTIONALITY
The Radiance+ RGBW Series utilizes switch logic to change backlight colors. To choose from one of the 8 available backlight color options:
- Switch backlight on-off-on-off within less than 1 second
- Continue switching off and on until desired color is selected
- Once desired color is selected, keep back light on for more than 1 second to save color – backlight color is locked in until process is repeated
NOTE: The Radiance+ RGBW lights contain a syncing function. Lights wired on the same circuit will sync together when color selection switch logic is initiated.
Order of backlight options:
- Red
- Green
- Blue
- Purple
- White
- Amber
- Light blue
- Rotating color mode
MOUNTING INSTALLATION INSTRUCTIONS
- Insert mounting brackets onto light as shown below.
- Secure hardware to a snug position and mount your light in desired location.
Pod and Scene SM
- A M6 Nylock Nut
- B M6-1×20 Socket Head
- C Mounting Bracket Bolt
- D 5/16-18×1 Carriage Bolt
- E 5/16 Flat Washer
- F 5/16 Lock Washer
- G 5/16-18 Nut
DXL
- A – 1/4-20 Socket Head Cap Screw
- B – 10-24 Socket Head Cap Screw
- C – 1/4” Flat Washer (2)
- D – #10 Flat Washer (2)
- E – Mount Bushing (2)
- F – 1/4-20 Nylock Nut
- G – 10-24 Nylock Nut
- H – Mount Bracket
- I – 3/8” Carriage Bolt
- J – 3/8” Flat Washer
- K – 3/8” Split Washer
- L – 3/8” Hex Nut
Light Bar
- A – 1/4” Nylon Locknuts (2)
- B – Mounting Bracket (2)
- C – Mount Bushing (2)
- D – 1/4 – 20×3/4” Hex Head Bolt (2)
- E – 1/4” Flat Washer (2)
RDS Light Bar
- A – 1/4” Nylon Locknuts (4)
- B – Mounting Bracket (2)
- C – Mount Bushing (2)
- D – 1/4 – 20×3/4” Hex Head Bolt (4)
- E – 1/4” Flat Washer (2)
WIRING HARNESS INSTALLATION INSTRUCTIONS
-
Always disconnect the negative battery terminal when working with any electrical circuits.
-
When routing wires through any metal or abrasive surfaces, be sure the surface is free of any sharp edges.
-
Match the light pigtail to the harness colors: Red to Red (Forward projecting LED +12v trigger), White to White (back-lighting LED +12v trigger), and Black to Black (shared ground) using butt connectors
-
Find a desired location for switches and drill a 3/4” hole for each switch.
-
Connect leads from wire harness to switch using the following diagrams.
- Route main power and ground leads from the harness to the battery terminals and attach the RED lead to battery +12v and the BLACK lead directly to the battery ground.
- Re-connect the negative battery terminal and test switches to verify functionality.
Your installation is now complete.
Welcome to the Rigid Nation!
WARRANTY
For warranty information, visit www.rigidindustries.com/about/warranty 779 N Colorado St, Gilbert, AZ 85233 • 855-760-5337 www.rigidindustries.com RIGID and Rigid Industries are registered and/or common law marks owned by JST Performance, LLC, a Delaware limited liability company d/b/a Rigid Industries.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>