RIGID 46598 Chase Lightbar Installation Guide

INSTALLATION INSTRUCTIONS
CHASE LIGHT BAR®

REPLACEMENT/ALTERNATIVE BRACKET KITS:
46598 – Chase Bar Tube Mount Kit/2
46599 – Chase Bar Surface Mount Kit/2

*THESE INSTRUCTIONS ARE FOR THE FOLLOWING LIGHTS: CHASE LIGHT BAR PN: 901801 & 901802

IMPORTANT

IMPORTANT
THANK YOU FOR PURCHASING RIGID INDUSTRIES’ PRODUCTS FOR YOUR VEHICLE. Please read through all of these Instructions and tips before proceeding with the installation. We do our best to provide a simple installation process for all applications however a professional installation is always recommended.
Always disconnect any power sources connected to your vehicle before servicing fuses or electrical systems.

MOUNTING INSTRUCTIONS

TUBE MOUNT

1. Place 4 square nuts into each channel on the back of the light

2. Align the 4 square nuts with the holes on each of the two mount pucks

3. Take the 8 socket head cap screws (shorter) and loosely screw them into the square nuts

4. Slide the mount pucks into the desired location and tighten the socket head cap screws to 6 in-lbs
   Note: For mounting on 1.50” tubing, install the included rubber spacers on the interior of the tube clamp.

5. Insert 2 rubber bumpers into the sides of each mount puck

6. Place the 2 tube clamps onto the vehicle

7. Insert 2 socket head cap screws (longer) into each tube clamp and loosely thread on a nut to each screw

8. Position the tube clamps to align with mount pucks

9. Slide the mount pucks over the tube mount screws. Tighten the tube mount screws to 6 in-lbs.

SURFACE MOUNT

1. Place 2 square nuts into each channel on the back of the light
2. Align the 2 square nuts with the holes on each of the two mount pucks
3. Take the 4 socket head cap screws (shorter) and loosely screw them into the square nuts
4. Slide the mount pucks into the desired location and tighten the socket head cap screws to 6 in-lbs
5. Place the surface mount brackets around the mount puck and insert 2 socket head cap screws (longer) through the mounts and pucks and loosely tighten a nut to each screw.
6. Install the mounts on a surface using the flat washer, lock washer, carriage bolt, and large hex nut.
7. Tilt the light to the desired angle and tighten the socket head cap screws (longer) to 6 in-lbs.
   Note: The surface mount can be mounted from the top or the bottom

WIRING INSTRUCTIONS

WIRING DIAGRAM

WIRING INSTRUCTIONS
The Chase light bar has a 6-wire ingress cable

• Red – Power and Running Mode
• Black – Common Ground
• White – Trigger 1
• Blue – Trigger 2
• Green – Trigger 3
• Yellow – Program wire

THE RED AND BLACK WIRE MUST BE CONNECTED FOR THE LIGHT TO FUNCTION, THE THREE TRIGGERS ARE OPTIONAL

• Connect the Red wire to 12V and the Black wire to ground
• Tap the Yellow program wire to 12V to cycle programs & select the desired running mode
• Once the mode is selected, stop tapping the Yellow wire. The mode is saved as the selected option for the Red wire.
• The red wire must be connected to 12V for the remaining triggers to be programmed and functional

PROGRAMMING THE TRIGGERS
NOTE: It is not required to program the three trigger wires

• With the Red and Black wires connected, connect the White Trigger 1 wire to 12v
• Tap the Yellow program wire to 12v to select the desired mode
• Once the mode is selected, stop tapping the Yellow wire to power. The mode is now saved as the selected option for the White wire.
• Connect the white wire to the appropriate circuit, ie brake, reverse, turn signal, switch, etc.
• Repeat the steps to program the Blue Trigger 2 wire and Green Trigger 3 wire
• When mode selection is complete, place a wire nut over the Yellow Program wire

. EACH WIRE HAS A SET PRIORITY LEVEL

• Highest Priority – Green – Trigger 3
• Next Highest Priority – Blue – Trigger 2
• Next Highest Priority – White – Trigger 1
• Lowest Priority – Red – Power
• If multiple triggers are powered the highest priority wire will overwrite or overlap the lower priority modes
• If the white Trigger 1 wire is connected to the brake circuit, when the brake is initiated it will overlap the running mode programmed on the red wire.

AVAILABLE MODES

AVAILABLE MODES

NOTES:

Your installation is now complete.
Welcome to the RIGID Nation
WARRANTY INFORMATION
For warranty information, visit www.rigidindustries.com/about/warranty
779 N Colorado St, Gilbert, AZ 85233 • 855-760-5337
www.rigidindustries.com
RIGID and Rigid Industries are registered and/or common law marks owned by JST Performance, LLC, a Delaware limited
liability company d/b/a Rigid Industries.
11-13819-A

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>