SwitchBot VA4NH1S28E Solar Panel User Manual

: June 3, 2024
: SwitchBot

Table of Contents

In the Box
Contact and Support
Device Instruction
Stick on Your Curtain
Install on SwitchBot Curtain U Rail
Install on SwitchBot Curtain Rod
Install on SwitchBot Curtain I Rail
Specification
Return and Refund Policy
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

:

SwitchBot Solar Panel
User Manual

In the Box

Contact and Support

Setup and Troubleshooting: support.switch-bot.com Support Email: support@wondertechlabs.com
Feedback:
Please send feedback via the SwitchBot App in the left side menu with the details of the issue.

Device Instruction

|
---|---

Stick on Your Curtain

If the Solar Panel cannot face direct sunlight, you can connect it with SwitchBot Curtain using the cable in the box and stick the Solar Panel on your curtain.

Open the case at the back and take out the cable.
Stick the 3 Loops onto the back of Solar Panel firmly and wait for 5 hours.
Stick the Hook firmly to a spot on your curtain where it is exposed to direct sunlight and the Solar Panel, while attached, can connect to a properly installed SwitchBot Curtain through its cable. Then Leave the Hook there for 5 hours.
Put the Solar Panel onto the Hook and connect the cable to your SwitchBot Curtain.

Install on SwitchBot Curtain U Rail

Note: at this moment, your SwitchBot Curtain should be already installed on your curtain track.

1. Take out the 2 handles.

| 2. Insert the 2 handles into the Hook Pairs and make sure it is firmly hanged.

---|---
3. Connect the Type-C connector to the SwitchBot Curtain.

| 4. You should see the Solar Panel and SwitchBot Curtain is securely connected.

Install on SwitchBot Curtain Rod

Note: at this moment, your SwitchBot Curtain should be already installed on your curtain track.

1. Take out the 2 handles.

| 2. Pull the SwitchBot Curtain down gently and insert the 2 handles into the Hook Pairs and make sure it is firmly hanged.

---|---
3. Connect the Type-C connector to the SwitchBot Curtain.

| 4. You should see the Solar Panel and SwitchBot Curtain is securely connected.

Install on SwitchBot Curtain I Rail

Note: at this moment, your SwitchBot Curtain should be already installed on your curtain track.

1. Take out the 2 handles.

| 2. Insert the 2 handles into the Hook Pairs and make sure it is firmly hanged.

---|---
3. Connect the Type-C connector to the SwitchBot Curtain.

| 4. You should see the Solar Panel and SwitchBot Curtain is securely connected.

Specification

Model Number: W1001000
Color: White / Black
Material: ABS plastic with UV-Resistant coating
Product Size: 72mm x 765mm x 25mm
Product Net Weight: 100g
Power: Solar Panel
Power Connection: 55cm USB Type-C cable
Setup Requirements: Direct sunlight
Output: 5V 250mA
Operating Conditions: -20°C~60°C / 10-90% RH

Return and Refund Policy

This product has one-year warranty (start from the purchasing day). The situations below do not fit the Return and Refund Policy

Intended damage or abuse.
Inappropriate storage (drop down or soaking in water).
User modify or repair.
Using loss.
Force majeure damage (Natural disasters).
Warning: Please avoid falling or any forms of physical impact.

CE Warning
Manufacturer’s Name: Woan Technology (Shenzhen) Co., Ltd.
Sample Description: SwitchBot Solar Panel
Trade Mark: SwitchBot
Model number: W1001000
Operating Temperature: -20°C~60°C

This product is a fixed location. To comply with RF exposure requirements, a minimum separation distance of 20cm must be maintained between the user’s body and the device, including the antenna. Use only the supplied or an approved antenna. This device in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. All essential radio test suites have been carried out.

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
The device complies with RF specifications when the device used at 20cm from your body.

FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
FCC RF exposure statement: The equipment complies with FCC Radiation exposure limit set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

www.switch-bot.com