SW-MOTECH ADV.07.664.75300/B ADVENTURE-SET BMW MIT Rally Seat Instruction Manual

SW-MOTECH ADV.07.664.75300/B ADVENTURE-SET BMW MIT Rally Seat

KFT.07.664.30001/B

PRO side carrier

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION

Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.

PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.

MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer · specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with a medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the vehicle manufacturer or by a specialist workshop!

FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

PRODUCT SPECIFIC INFORMATION

ATTENTION: The indicated maximum load is inclusive the weight of case/luggage and adapter kit The maximum vehicle load specified by the manufacturer must not be exceeded! The side carriers are designed exclusively for the use of SW-MOTECH Adapter Kits. Dismount the side carriers when travelling without cases/luggage. Always use the side carriers in pairs.

ATTENTION: Make sure that after attaching the luggage to the vehicle it is NOT in the exhaust flow! Dangers of burns!

• Errors and omissions excepted. Technical and design modifications are subject to change .

PARTS LIST

• All measurements in millimeters.
• The second number indicates the total quantity of the part in the delivery.
• No torque specifications: Use the torque defined by the vehicle manufacturer
• The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING

• Loosen the marked screws of the exhaust cover and remove it from the vehicle.

• Loosen the shown exhaust screw and clamp. Carefully remove the silencer from the vehicle.

• Loosen the screws of the passenger footrests and remove it from the vehicle. Attach the mounting tabs (1) to the vehicle, as shown in the drawings. Attach the mounting tab on the left side of the vehicle as same as on the right side.
  ATTENTION: Use liquid thread locker! Do not fully tighten the screws yet. Reattach the parts that were removed in step [1] and 12].

• Remove the seat. Remove the marked screws from the vehicle.

NOTE: Pay attention to the mounting situation with the SW-MOTECH luggage rack lowering kit, shown in the detailed drawing. The front spacers of the Lowering Kit are not needed for mounting. Attach the mounting tabs (3) with the original screws (Orig.) to the vehicle, as shown in the drawing.

ATTENTION: Use liquid thread locker! Do not fully tighten the screws yet .

• Attach the crossbar (5) to the license plate mount, as shown in the drawing. Do not fully tighten the screws yet.
• Connect the side carriers (9) and (10) to the mounting tabs and crossbar with the fasteners (11). Secure the fasteners with the lock washers. Once all the parts are evenly positioned without excess tension, tighten the screws as specified in the parts list. Tighten the original screws (Orig.) with the manufacturer’s specified torque.
  NOTE: The Anti-Theft Device is sold separately.

KFT.00.152.35100

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Installation and/or maintenance of this product requires good technical understanding! For your own safety, SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behavior and/or stability of your vehicle.

GENERAL INFORMATION

Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.

PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.

MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer · specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with a medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the vehicle manufacturer or by a specialist workshop!

FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also, make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

PARTS LIST

• All measurements in millimeters.
• The second number indicates the total quantity of the part in the delivery.
• No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING

NOTE: The illustration shows the mounting to the right PRO side carrier. Mount the parts to the left PRO side carrier in the same way as to the right PRO side carrier. Attach the shown parts to your PRO side carriers (sold separately). Tighten the screws as specified in the parts list.

ATTENTION: To ensure the proper fit of your TRAX ADV / EVO / ION side case, adjust the latch hook (1) over the elongated holes (see detail drawing)! Make sure that the side case’s latch engages properly when mounted!

ALK.00.733.10000 / 11000 / 15000

Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. » www.sw-motech.com Installation and/or maintenance of this product require good technical understanding. For your own safety SW- MOTECH recommends having installation and/or servicing carried out by a specialist workshop. SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work.
Carefully follow all the directions given in the mounting instructions. Also pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as reference.
This product was developed for vehicles in their original condition. Compatibility with original accessory parts or other manufacturers accessory parts is not guaranteed. Installed accessories can change driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION

Observe any country-specific legal or TOV regulations. If required, enter the installed parts into the vehicle documents with the appropriate inspection authority.

SECURITY
Please pay attention to the following information concerning the TRAX ADVENTURE ALU-BOX: The TRAX ADVENTURE ALU-BOX is designed exclusively for mounting on SW-MOTECH QUICK-LOCK side carriers, QUICK-LOCK adapter plate an STEEL-RACK adapter kit. Modifications made to the cases will void any warranty.

• ATTENTION: Riding with TRAX ADVENTURE ALU-BOX may affect the motorcycle’s driving and braking performance.
• ATTENTION: TRAX ADVENTURE ALU-BOXES M & L must be used in pairs. Make sure the weight is evenly distributed between left and right side case.
• ATTENTION: Maximum load: Please refer to the mounting instructions of the SW-MOTECH QUICK-LOCK side carrier, ALU-RACK or STEEL-RACK. Maximum speed with mounted cases: 130 km/h (80 mph).
• ATTENTION: Make sure that the TRAX ADVENTURE ALU-BOX is properly attached to the particular adapter and fully engaged to all four mounting points! ALL latches of the TRAX ADVENTURE ALU-BOX must be locked BEFORE riding with the TraX ® EVO / TRAX ADV lock cylinder set (sold separately) and remain closed while riding. Improperly mounted cases run the risk of detaching during transport.

CARE
To clean the TRAX ADVENTURE ALU-BOX, use warm, soapy water and a soft, clean cloth. Rinse with clean water. Do NOT use strong cleaning agents, rough cleaning tools or high-pressure washer!

PARTS LIST

• All measurements in millimeters.

• www.sw-motech.com

Please visit our webshop for application charts and compatible accessories.

LID AND LOCK CYLINDER SET

Open the lid (TRAX ADV M / L / topcase)

1. Pull the latch of the lid upwards
2. and remove it from the latch bar.
3. Open the lid.

*Insertion of the Trax® EVO / TRAX ADV lock cylinder set (TRAX ADV M / L / Topcase)**

1. Insert the lock cylinders into the latches.

2. Secure the lock cylinders with the clamping plates.
   ATTENTION: Pay attention to the correct alignment of the clamping plates (as shown in the detail drawings).

3. Insert the keys into the lock cylinders; open or close the lock cylinder as shown in the schematic drawing.

ATTENTION: Use for lubrication graphite powder ONLY!

• Sold separately.

LID LIMITER

Mounting the lid limiters [TRAX ADV M / L / top case)

1. Open the lid. Attach the snap-fit (4) with the shown parts at the lid frame. Tighten the screws as specified in the parts list.

2. Attach the lid limiters (5) with the shown parts at the case frame.
   NOTE: Pay attention to left-right specifications for the limiters (in driving direction). Tighten the screws as specified in the parts list. Press the lid limiters onto the snap-fits.

3. Before closing the lid for the first time, the lid limiters must be compressed as shown in the drawing. While closing the lid, make sure that the lid limiters are not pinched between lid and case.

4. To remove the lid from the case (as shown on page 5). remove the lid limiters from the snap-fits first.

QUICK RELEASE FASTENER

Removing the lid (TRAX ADVENTURE M / LI

1. Press the quick-release fastener down until it clicks into place and the button pops out.

2. Then remove the lid from the case.
   NOTE: If you have installed the lid limiters (5), they must be detached before removing the lid (as shown on page 4).

3. Press the button of the quick-release fastener to lock the replaced lid in place. Make sure that the quick-release fastener snaps above.

Maintenance and cleaning of the quick-release fastener (TRAX ADVENTURE M / LI

1. Loosen the six screws on the inner side of the case and remove the quick-release fastener.
2. Loosen the screw of the button (fix with thumb and index finger].
3. Loosen the shown clip carefully and.
4. remove the quick-release fastener and springs from the mounting plate.
5. Clean the components with clean water and let it air dry. Reattach all arts in reversed order.

Attachement of TRAX ADVENTURE ALU-BOX M & L

1. Lead the four openings of the mounting rails onto the locating bolts of the mounted QUICK-LOCK adapter kit.
   Then press the TRAX ADVENTURE ALU-BOX slightly downward, until it properly rests on the QUICK-LOCK side carrier.
   ATTENTION: Make sure that all four locating bolts rests on at the same time.

2. Place the latch over the latch hook and …

3. close the latch; check the proper fit of the TRAX ADVENTURE ALU-BOX on the QUICK-LOCK side carrier.

   • ATTENTION: Make sure the closed latch is under sufficient tension! If not the latch hook must be readjusted!
   • ATTENTION: Secure the TRAX ADVENTURE ALU-BOX with the separately available Trax® EVO / TRAX ADVENTURE lock cylinder set at the QUICK-LOCK side carrier before riding!

Attachement of TRAX ADVENTURE ALU-BOX M & L

1. Lead the four openings of the mounting rail onto the locating bolts of the mounted QUICK-LOCK adapter plate/ STEEL-RACK adapter kit.
   Then press the TRAX ADVENTURE ALU-BOX slightly forward, until it properly rests on QUICK-LOCK adapter plate/ STEEL-RACK adapter kit.
   ATTENTION: Make sure that all four locating bolts rests on at the same time.

2. Place the latch over the latch hook and …

3. close the latch; check the proper fit of the TRAX ADVENTURE ALU-BOX on the QUICK-LOCK Adapter Plate/ STEEL-RACK Adapter Kit.

• ATTENTION: Make sure the closed latch is under sufficient tension! If not the latch hook must be readjusted!
• ATTENTION: Secure the TRAX ADVENTURE ALU-BOX with the separately available Trax® EVO / TRAX ADVENTURE lock cylinder set at the QUICK-LOCK adapter plate/ STEEL-RACK adapter kit before riding!

Anti-theft protection for PRO side carrier

Each of this pair of lockable side carrier fasteners can be used to replace a standard fastener on a PRO side carrier in order to provide theft protection. The set includes two matched keys.

Attention: To maintain locks use graphite powder only.

GPT.07.904.19100/B

ADVENTURE-RACK

Thank you for choosing this premium product from SW-MOTECH. Please carefully read and understand all instructions, safety messages and warnings in this mounting instructions prior to installation and use of this product to avoid injury. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Keep these mounting instructions as reference. SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!

SAFETY ALERT SYMBOL

A This safety alert symbol is used throughout these mounting instructions to warn of the possibility of death, bodily injury or other warnings. The words DANGER, WARNING and CAUTION are used with this safety alert symbol to convey important safety messages and information related to the installation and use of this product. These words along with the safety alert symbol mean:

• DANGER: Indicates a hazardous situation that, if not avoided, will result in death or serious injury!
• WARNING: Indicates a hazardous situation that, if not avoided, could result in death or serious injury!
• CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury!
• NOTICE: Important information, but not death or injury related (property damage only)!
• WARNING: The installation and/or maintenance of this product requires advanced mechanical skills, the proper tools, and a thorough understanding of tool use and torque specifications. For your own safety, SW-MOTECH recommends having installation and/or maintenance carried out by a qualified and certified motorcycle mechanic.
• WARNING: Should you choose to self-install this product, carefully and completely read all intallation and safety instructions before installation and use, and follow all the directions and safety precautions given in the mounting instructions to avoid serious injury or death. Also pay attention to all relevant information in the vehicle manual during installation and use. IF YOU DO NOT UNDERSTAND ANY PART OF THESE INSTRUCTIONS OR NEED CLARIFICATION OF ANY INSTRUCTION, DO NOT ATTEMT TO MOUNT THIS PRODUCT WITHOUT CONTACTING SW-MOTECH FOR ASSISTANCE.
• PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included.
• CAUTION: Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the engine/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools and wear always safety glasses and hand protection. Have another person help you.
• MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer’s specifications or replaced by parts and hardware delivered by SW-MOTECH.
• WARNING: Secure all threads, unless otherwise specified, with medium­strong strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a certified motorcycle workshop!
• FUNCTION CHECK: After installation also make sure that no moving parts are obstructed, and function of the vehicle is not hindered in any way. Cables and hoses must not rub and/or be pinched.
• WARNING: Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all connections and the proper fit of the product. Installed accessories can change driving behavior/stability of the vehicle.

PARTS LIST

Note:

• All measurements in millimeters.
• The second number indicates the total quantity of the part in the delivery. No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it IS within the vehicle manufacturer’s specifications.
• WARNING: Always wear eye and hand protection!
• WARNING: Always use appropriate tools! Remove the original screws from the mounting points. Attach the mounting bracket (1 l to the luggage rack, as shown in the drawing.
• WARNING: Use a liquid thread locker! Tighten the screws with the manufacturer-specified torque.

Assembly side with carrier SW-MOTECH
For mounting the luggage rack together with the side carrier, attach the mounting bracket (1] with the mounting brackets of the side carrier, as shown in the drawing.

• WARNING: Use liquid thread locker! Tighten the screws with the manufacturers’ specified torque.

NOTICE: Depending on the available space, attach the luggage rack to the marked mounting position (AJ or (BJ, as shown in the detail drawing.  Attach the luggage rack [10) to the mounting bracket [1 ), as shown in the drawing.

WARNING: Use liquid thread locker! Tighten the screws as specified.

PRODUCT SPECIFIC INFORMATION

WARNING: The indicated maximum load is inclusive the weight of topcase/luggage and adapter kit! The maximum vehicle load specified by the manufacturer must not be exceeded!

GPT.00.152.35100/B

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behavior and/or stability of your vehicle.

GENERAL INFORMATION

Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.

PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.

MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer · specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with a medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the vehicle manufacturer or by a specialist workshop!

FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also, make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

PARTS LIST

• All measurements in millimeters.
• The second number indicates the total quantity of the part in the delivery.
• No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

ADVENTURE RACK
Attach the shown parts to your ADVENTURE RACK (sold separately).

• ATTENTION: Use liquid thread locker (screws (6) only)! Tighten the screws as specified in the parts list.
• ATTENTION: To ensure the proper fit of your TRAX ADV/EVO/ION top case, adjust the latch hook (1) over the elongated holes (see detail drawing)! Make sure that the topcase’s latch engages properly when mounted!

Adapter plate for STREET-RACK
Attach the shown parts to your adapter plate for STREET-RACK [sold separately]. Tighten the screws as specified in the parts list.

ATTENTION: To ensure the proper fit of your TRAX ADV/EVO/ION topcase, adjust the latch hook (1 I over the elongated holes (see detail drawing)! Make sure that the topcase’s latch engages properly when mounted!

BC.ALK.00.732.10700/B

TRAX M/L expansion bag

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.

SECURITY
Please pay attention to the following product information: Modifications will void any warranty.

• ATTENTION: Riding with the TRAX expansion bag may affect the motorcycle’s driving and braking performance.
• ATTENTION: Maximum load: Please refer the manual instructions of the SW-MOTECH side sarriers and the TRAX aluminium case, but not more then 2 kg. The maximum vehicle load specified by the manufacturer must not be exceeded! Maximum speed with mounted TRAX expansion bag: 130 km/h!
• ATTENTION: BEFORE riding make sure that the TRAX expansion bag is properly attached. Check the proper fit at each stop!
• ATTENTION: All parts of the TRAX expansion bag must not contact any hot or moving parts of the vehicle. All parts should also remain 5 cm away from the exhaust and remain clear of the exhaust stream. All strap ends should be secured so they can not blow around once the vehicle is in motion. Dropping the motorcycle or improper handling can damage the outer surface of the TRAX expansion bag. Never store pointy or sharp-edged objects in bags, which could cause injury to persons or damage to the vehicle/product.

CARE
To clean the TRAX expasion bag use warm, soapy water and a soft, clean cloth. Rinse with clean water. Do NOT use strong cleaning agents, rough cleaning tools or high pressure washer! Clean the TRAX expansion bag after riding in salty conditions, to avoid damage from salt.

• ATTENTION: Surface materials can experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors (e.g., SMOG, acid rain, etc.)! SW-MOTECH assumes no liability for this.
• ATTENTION: Dirt on the product and vehicle has an abrasive effect and can damage surfaces. Make sure that all areas of the case, which have contact with the product, are protected with an adhesive protection film from scratches and abrasions. SW-MOTECH assumes no liability for paint damage and abrasions.

FIXATION

Place the TRAX expansion bag on the lid of the TRAX aluminum box or a similar aluminum case. Fix all four straps of the TRAX expansion bag to the tie-down points of the lid, as shown in the lower detail drawings. Now tighten the straps until the TRAX expansion bag is centered and sits firmly on the lid. Make sure that the strap ends are secured against fluttering.

• Errors and omissions excepted. Technical and design modifications are subject to change.

SW-MOTECH GmbH & Co. KG

• Ernteweg 8/10 35282 Rauschenberg Germany
• Tel. /phone + 49 (0)6425 / 8168 – 050
• Fax / fax + 49 (0]6425 / 8168 – 10
• info@sw-motech.com
• www.sw-motech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>