Reyee REX12 WiFi Extender Booster Signal Repeater User Manual
- June 12, 2024
- REYEE
Table of Contents
Reyee REX12 WiFi Extender Booster Signal Repeater
Product Appearance
- Ethernet Port
- System Status LED
- Signal Status LED
- Mesh/WPS Button
Package Content
- Range Extender
- 1 User Manual
- 1 Warranty Card
Set-Up
Scenario 1: Connect to Reyee Device (Reyee Mesh)
- Plug the extender halfway between your Reyee router and Wi-Fi dead zone (within router signal range). Wait until turns solid green.
- Click the Mesh button on your primary Reyee router (Not the extend-er). Wait until turns solid white.
Note: Short press the Reyee 4 to turn off the LED.
Scenario 2: Connect to Other Brand Router
- Plug the extender halfway between your router and Wi-Fi dead zone (within router signal range). Wait until 2 turns solid green. This might take up to 1-2 minutes.
- Connect your computer or smartphone to SSID “@Reyee-sXXXX”, the instruction GUI launches automatically when you connect the SSID. Follow the instructions to complete the setup. If it does not auto-launch, visit “http://10.44.77.254″ to configure the extender.
- The 3 should turn solid white, indicating a successful connection to the router.
Note: If the signal 3 lights only one bar, plug the extender closer to your router.
Scenario 3: Connect via WPS
- Plug the extender halfway between your router and Wi-Fi dead zone (within router signal range). Wait until 2 turns solid green.
- Press the WPS button on your router.
- Within 2 minutes, press the WPS button on the extender. Wait until turns solid white.
- If the extender connects to a dual-band router, it will boost the 5G Wi-Fi signal.
- If you click the WPS button when the device is already in WPS networking condition, it will not be paired again.
Scenario 4: Connect to the Modem
- 1. Plug the extender next to your modem. Wait until 2 turns solid green.
- Connect to the modem with an Ethernet cable. Wait until 2 turns solid green.
- Connect your computer or smartphone to SSID “@Reyee-sXXXX”, or visit “http://10.44.77.254” to configure the extender.
Note: Connect a modem for uninterrupted connection via the 100Mbps Ethernet port.
LED Descriptions
System Status LED
| Status | Description |
|---|
Green
| Solid on| The device works properly. / Connection success.
Blinking| The system is starting up / restoring factory settings.
Orange
|
Solid on
| The device fails to access Wi-Fi network of the primary router.
Blinking
| The device to accessing Wi-Fi network of the primary router.
Red| Solid on| The network is unreachable.
Signal Status LED
| Status | Description |
|---|---|
| Blinking | Connection in progress. |
White
| Three bars on| Best connection.
Two bars on| Good connection.
One bar on| Poor connection.
Off
| 1. The device is set to router mode.
2. Connection failed.
Access Extender Settings
- Via Reyee App: Download the Reyee Router App to get advanced features, such as turning off the LED, and setting the Wi-Fi name and password.
- Via Web Browser: Visit http://10.44.77.254 to view or change extender settings
Troubleshooting
-
Locate the extender properly
If only one signal bar lights up after setting up, plug the extender closer to your router.
Plug the extender halfway between your router and Wi-Fi dead zone (within router signal range). -
Reset the extender
Press the Reyee Mesh button 4 for more than 5 seconds. If the 2 is blinking, the device is restoring factory settings.
Wait for 1 to 2 minutes. When the 2 turns solid on, the device has restored factory settings.
Repeat the configuration after the device reboots. The default SSID is @Reyee- sXXXX. -
Management Password
You are advised to enter the Wi-Fi password. If the password is still incorrect, please restore the device to factory settings (Press the Reyee Mesh button 4 for 5 seconds).
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference in radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Statement:
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules.
RF Exposure Warning!
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna or
transmitter.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
IMPORTANT!
Operation in the band 5150-5250 MHz is only for indoor use.
Innovation, Science and Economic Development Canada Statement
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Exposure Statement
The device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS‐102 RF exposure,us-ers can obtain
Canadian information on RF exposure and compliance.
Frequently Asked Questions
What is the Reyee REX12 WiFi Extender Booster Signal Repeater?
The Reyee REX12 is a device designed to extend the range and improve the signal strength of your existing WiFi network.
How does the Reyee REX12 WiFi Extender work?
The Reyee REX12 connects to your existing WiFi network and amplifies the signal, allowing it to reach areas of your home or office where the WiFi signal is weak or non-existent.
Does the Reyee REX12 support dual-band WiFi?
Yes, the Reyee REX12 supports both 2.4GHz and 5GHz WiFi bands, providing you with the flexibility to choose the band that works best for your devices.
What is the maximum coverage range of the Reyee REX12 WiFi Extender?
The coverage range of the Reyee REX12 can vary depending on various factors such as the environment and obstacles, but it is designed to cover an area of up to 1,200 square feet.
Does the Reyee REX12 require a separate power source?
Yes, the Reyee REX12 needs to be plugged into a power outlet for it to function.
Is the Reyee REX12 easy to set up?
Yes, the Reyee REX12 is designed to be easy to set up. It typically involves connecting the device to your existing WiFi network using a mobile app or a web interface.
Can the Reyee REX12 work with any WiFi router?
Yes, the Reyee REX12 is compatible with most standard WiFi routers and can work with any brand or model.
Can the Reyee REX12 extend the WiFi signal outdoors?
While the Reyee REX12 is primarily designed for indoor use, its signal may extend to outdoor areas depending on the environment and obstacles.
Does the Reyee REX12 support WPA2 security?
Yes, the Reyee REX12 supports WPA2 encryption, which ensures a secure connection between your devices and the WiFi extender.
Can I connect multiple devices to the Reyee REX12 at the same time?
Yes, the Reyee REX12 can handle multiple devices simultaneously, allowing you to connect smartphones, tablets, laptops, smart TVs, and other WiFi-enabled devices.
Does the Reyee REX12 have an Ethernet port?
Yes, the Reyee REX12 typically comes with an Ethernet port, allowing you to connect wired devices to the extender for a stable and reliable connection.
Can I use multiple Reyee REX12 extenders to create a mesh network?
The Reyee REX12 is not specifically designed for creating a mesh network. However, you may be able to use multiple extenders in conjunction with your existing router to extend the WiFi coverage throughout your home or office.
Video Introductory OF Wifi Extender
Download this PDF Link:Reyee REX12 WiFi Extender Booster Signal Repeater User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>