REYEE RG-E3 Wi-Fi 6 AX1800 Smart Wi-Fi Mesh Router User Manual
- June 6, 2024
- REYEE
Table of Contents
Reyee RG-E3 Wireless Router
User Manual
https://cloud.ruijienetworks.com/shinya
Packing List
| Name | Quantity | Unit |
|---|---|---|
| Router | 1 | Set |
| Power Adapter | 1 | Piece |
| Warranty Card | 1 | Copy |
| User Manual | 1 | Copy |
| Network Cable | 1 | Piece |
Appearance
Please connect the power and network cables as shown below.
Indicator
Reyee Mesh Indicator
Green| Blinking| The device is being paired.
Steady on| The device is paired and Wi-Fi signal is normal.
Orange| Steady on| The device is paired but Wi-Fi signal is weak.
Red| Steady on| The device pairing is disconnected.
System Status Indicator
Blue| Steady on| The device is running normally.
Blinking| Restoring the factory settings or restarting.
Network Connection
Scenario 1: Configure a single router
After you connect the cable and power the router on, it will start up in 2 to
3 minutes. Wait until the system status indicator turns into steady blue and
the router broadcasts the SSID (@Reyee-sXXXX by default).
Access the Internet by Web browser：
-
Connect to the SSID @Reyee-sXXXX, and the configuration page will be displayed automatically; if not, please visit 192.168.110.1.
-
The router will match the Internet access method. Please configure the network parameters accordingly.
-
configuration working, you can connect to the SSID and access the Internet. Configure the SSID and password. After the
Access the Internet by App：
https://cloud.ruijienetworks.com/shinya
Scenario 2: Reyee Mesh
-
Place the second router within 2 meters of the first one, and power it on.
After the system status indicator blinks in blue, wait for 2 to 3 minutes until it turns into steady blue. (If the router had been configured before, please press the Reset Button for more than 3 seconds to restore the factory settings)
-
Press the Reyee Mesh button on the first router.
Press the Reyee Mesh button on the first router, and its indicator will blink in green during searching for routers. The indicator on the second router will also blink in green slowly during pairing. After 2 minutes, as the indicators on both routers turn into steady green, the pairing succeeds.
- Please note that Wi-Fi signal may be weak if two routers are placed far from each other or there are several obstacles like walls between them.
- The Internet speed may be slow if there are multiple paired routers. We recommended mesh-up within 5 routers (1+4) to keep good performance.
FAQs
-
What to do if I forget the management password?
Try the Wi-Fi password which may be the same with the management password. If not, please restore the factory settings. -
How to restore the factory settings?
Power on the router and wait for 2 to 3 minutes until it starts up. Press the Reset button for more than 3 seconds until the system status indicator blinks. After the indicator changes to steady on and the SSID “@ Reyes-sXXXX” is broadcast, the router restores the factory settings successfully. -
Can I connect multiple routers with network cables?
Yes, and the wired connection is more stable. You can connect the WAN port (yellow) from a secondary device with the LAN port (black) from a master router for a wired connection.
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
RF Exposure Statement:
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules.
RF Exposure Warning!
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna or
transmitter.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
IMPORTANT!
Operation in the band 5150-5250 MHz is only for indoor use.
Innovation,Science and Economic Development Canada Statement
This device complies with Industry Canada’s license-exempt RSS. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that
may cause undesired operation of the device.
Exposure Statement ：
The device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS ‐102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
RF Exposure Warning!
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. This equipment should be installed and operated
with a minimum distance of 20 centimeters between the radiator and your body.
5G UNII-1 Statement ：
- The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
- DFS (Dynamic Frequency Selection) products operate in the bands 5250-5350 MHz, 5470-5600MHz, and 5650-5725MHz.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>