REYEE RG-E5 Mesh Smart WiFi 6 Router User Manual
- June 6, 2024
- REYEE
Table of Contents
Reyes RG-E5 Mesh Router
User Manualhttps://cloud.ruijienetworks.com/shinya
Packing List
| Item | Quantity |
|---|---|
| Router | 1 |
| Power Adapter | 1 |
| Warranty Card | 1 |
| User Manual | 1 |
| Ethernet Cable | 1 |
| Regulatory Compliance Manual | 1 |
Product Appearance
Reyes Mesh Indicator
| Status | Description |
|---|---|
| Blinking green | The device is being paired. |
| Solid green | The Mesh network signal is strong. |
| Solid orange | The Mesh network signal is weak. |
| Solid red | The Mesh network is disconnected or not set up. |
System Status Indicator
| Status | Description |
|---|---|
| Solid blue | The device is working normally and can access the Internet. |
| Blinking blue | The device is starting up or restoring the |
factory settings.
Scenario 1: Configure one single router to access the Internet
- Power on and connect Ethernet Cable.
- Configure the router.
The router will complete startup in 2 to 3 minutes after being powered on. Wait until the system status indicator turns solid on and the SSID is broadcast (default SSID:
@Reyee-sXXXX).
Access the Internet by Web
① Go to your phone settings page and choose Wi-Fi network @Reyee-sXXXX, and the configuration page will appear automatically. Or you can access 192.168.110.1 via the browser.
② The router automatically detects the type of Internet connection. Please configure the network parameters accordingly.
③ The Wi-Fi configuration takes effect in 2 to 3 minutes. Connect to the new Wi-Fi name (SSID) after it appears in the Wi-Fi list for Internet access.
Access the Internet by App
① Download the Reyes Router App
https://cloud.ruijienetworks.com/shinya
② Create an account by one click
③ Tap Add Router, and follow the guide of configuration
Scenario 2: Configure more than one router to set up a Mesh network
To cover every corner of a villa, a large house, or a condo, you can buy
multiple Reyes Mesh routers to form a mesh network for full-house coverage.
-
Make the primary router connect to the internet Please refer to Scenario 1 for configuration.
-
Place the secondary router within a maximum distance of 2 meters(around 6.5ft) from the primary router, and power it on Wait for 2 to 3 minutes until the system status indicator on the secondary router turns solid on. If the router has been configured before, please use a pin to press Reset Button for over 3 seconds to restore the factory settings.
-
Press the Reyes Mesh button on the primary router
The Reyes Mesh indicator on the primary router will blink in green, indicating that the primary router is searching nearby routers for pairing. The Reyes Mesh indicator on the secondary router will also blink in green, indicating the secondary router is being paired with the primary router. In about 2 minutes, the Reyes Mesh indicators on both routers will turn solid green, indicating Mesh pairing is complete. -
Place the secondary router in an area where the Wi-Fi signal is weak or nonexistent, and power it on again
Wait for 3 to 5 minutes until the Reyes Mesh indicator on the secondary router turns solid on. The original SSID of the secondary router (@Reyee-sXXXX) will disappear and both routers will broadcast the same SSID, indicating that Mesh networking succeeds. You can also set up a wired connection between two routers as shown below.
- Determine the placement and distance by referring to the signal strength visualized by Reyes Mesh indicators on the top.
- Please find the proper location for both routers. Do not place two routers too far away from each other and avoid too many walls or other obstacles between them.
- If you have three or more routers, you can pair them by one-click Reyes Mesh during startup, or repeat steps 2 to 4 to connect them one by one. A Reyes mesh network consists of up to five routers (one primary router and four secondary routers).
FAQs
① What can I do if I forget the management password?
Try the Wi-Fi password which may be the same as the management password. If it
does not work, please restore the device to factory settings.
② How to restore the factory settings?
Power on the router and wait for 2 to 3 minutes until it completes startup.
Use a pin to press the Reset Button for over 3 seconds until the system status
indicator starts blinking, and then release the button. After the system
status indicator turns solid on, the router will broadcast SSID @Rey-ee-sXXXX,
indicating that the router is restored to factory settings successfully.
③ Can I connect routers with an Ethernet cable?
Yes, and the wired connection is more stable. Insert one end of the Ethernet
cable into the WAN port (yellow) of the secondary router and connect the other
end to the LAN port (black) of the primary router.
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna
-Increase the separation between the equipment and receiver
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
RF Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules.
RF Exposure Warning!
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna or
transmitter.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
IMPORTANT!
Operation in the band 5150-5250 MHz is only for indoor use
Innovation, Science and Economic Development Canada Statement
This device complies with Industry Canada’s license-exempt RSS. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Exposure Statement ：
The device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS ‐102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
RF exposure warning!
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. This equipment should be installed and operated
with a minimum distance of 20 centimeters between the radiator and your body.
5G UNII-1 Statement ：
- The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
- DFS (Dynamic Frequency Selection) products operate in the bands 5250-5350 MHz, 5470-5600MHz, and 5650-5725MHz.