BROAN NuTone 1103435 Overture Room Sensor User Manual
- June 5, 2024
- Broan NuTone
Table of Contents
NuTone
Overture™ ROOM SENSOR
INCLUDED
Room Sensor Part No. 1103435
User Manual
Quick Start Guide
CONTROL SPECIFICATIONS
- cULus Listed
- 120 VAC 60 Hz Line Power
- Requires NEMA 5-15R or 5-20R Receptacle
- Maximum load ½ HP Motor, 15A Resistive,15A Inductive, 3A Incandescent, 0.6A Electronic Ballast
- For Control of Electronic Ballast, CFLs, LED, and LED lamps
- Operating temperature: 32-95°F (0-35°C)
- Purpose of Control: Operating Control
- Rated impulse voltage: 1500 V
SAFETY
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
-
Install only in a UL Listed NEMA 5-15R or NEMA 5-20R receptacle. The socket outlet shall be installed near the equipment and shall be easily accessible.
NOTE: This device shall not be used in combination with a wall switch- controlled receptacle. -
The automatic operation feature is Type 1.C action, according to UL 60730-1.
-
The enclosure protection rating is IP10.
-
The product is Pollution Degree 2, which is intended to be used in a household environment or similar.
-
The devices are not intended for use in locations where the temperature may be less than actual room conditions, such as unheated warehouses or garages.
-
Avoid water and wet locations. Keep the device away from water, fire, excessive humidity, or hot environments.
-
Do not use the device where wireless devices are not allowed.
-
For passthrough devices, plug the power strips into the integrated electrical sockets of the devices, but devices of the same or another type not be stacked in normal use.
-
Do not attempt to disassemble, repair, or modify the device. Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.
-
Note: When power is applied, the Room Sensor may require approximately 30 seconds to boot up and be ready to function.
-
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your own risk.
INSTALLATION
- Verify Room Sensor orientation before installation. Note the “TOP” direction shown on the Room Sensor label.
- Location Notes:
a. Placing the Room Sensor directly above a heater or near drafts is NOT recommended. Ideal places for room sensors are bedrooms, family/living rooms, dens, laundry rooms, etc. Be sure Room Sensor has adequate airflow in order to have high-performance monitoring. Placing directly behind a dresser, couch, etc. will prohibit adequate airflow.
b. For bathroom applications, the Room Sensor should be placed in close proximity to the shower/tub/sink, etc. (the main source of humidity and steam/VOCs) and at sink height or higher for effective monitoring of your indoor air quality.
c. Place your Room Sensor within the range of your Wi-Fi router or access point (approximately 100 feet).
d. Avoid physical obstructions and radio interference in the surrounding area.
e. Download the Broan-NuTone Overture TM App for step-by-step set-up instructions to connect your Room Sensor to the Overture TM system. Scan QR code to go to App Store.
Regulatory Information
The Overture™ Room Sensor 1103435 is certified to comply with applicable FCC
and IC rules and regulations governing RF and EMI emissions. Refer to 1103435.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation. The distance
between user and device should be no less than 20 cm.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician to help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ISED Compliance Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Broan-NuTone LLC is under
license. Other trademarks and trade names are those of their respective
owners.
The Android robot is reproduced or modified from work created and shared by
Google and used according to terms described in the Creative Commons 3.0
Attribution License.
Regulatory ID for 1103435 Overture™ Room Sensor
FCC ID: 2ADLL-1103435
IC: 2143B-1103435 CAN ICES-003(B) / NMB-003(B)
Made in China to the quality standards and specifications of Broan-NuTone LLC,
926 West State Street, Hartford,
Wisconsin, USA 53027 Broan-NuTone.com
800-558-1711
Venmar Ventilation ULC, 550 Lemire Blvd., Drummondville Québec, Canada J2C 7W9
Broan-NuTone.ca 800-567-3855 For more
information and user manuals scan QR code below.
For Warranty Statement, Service Parts, Technical
Support, or to Register your product, please visit our
website or call: In the United States –
Broan-NuTone.com 800-558-1711. In
Canada –
Broan-NuTone.ca 800-567-3855
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>