REYEE RG-REX12 Wi-Fi Range Extender User Manual

RG-REX12 Wi-Fi Range Extender
User Manual

Scan to Download Reyee Router App
For technical support, please email:techsupport@ireyee.com
Technical support site: https://www.ireyee.com/support

Product Appearance

1. Ethernet Port
2. System Status LED
3. Signal Status LED
4. Mesh/WPS Button

Package Contents：

Range Extender 1 User Manual 1 Warranty Card *1
Set-Up

Scenario 1: Connect to Reyes Device (Reyes Mesh)

1. Plug the extender halfway between your Reyes router and Wi-Fi dead zone (within the router signal range). Wait until turns solid green.
2. Click the Mesh button on your primary Reyes router (Not the extender). Wait until turns solid white.

Note: Short press the Reyes to turn off the LED.

Scenario 2: Connect to Other Brand Router

1. Plug the extender halfway between your router and Wi-Fi dead zone (within the router signal range). Wait until turns solid green. This might take up to 1-2 minutes.
2. Connect your computer or smartphone to SSID “@Reyee-sXXXX”, the instruction GUI launches automatically when you connect the SSID. Follow the instructions to complete the setup. If it does not auto-launch, visit “http://10.44.77.254” to configure the extender.
3. They should turn solid white, indicating a successful connection to the router.

Note: If the signal lights only one bar, plug the extender closer to your router.

Scenario 3: Connect via WPS

1. Plug the extender halfway between your router and Wi-Fi dead zone (within router signal range). Wait until turns solid green.
2. Press the WPS button on your router.
3. Within 2 minutes, press the WPS button on the extender. Wait until turns solid white.

1. If the extender connects to a dual-band router, it will boost the 5G Wi-Fi signal.
2.  If you click the WPS button when the device is already in WPS networking condition, it will not be paired again.

Scenario 4: Connect to the Modem

1. Plug the extender next to your modem. Wait until turns solid green.
2. Connect to the modem with an Ethernet cable. Wait until turns solid green.
3. Connect your computer or smartphone to SSID “@Reyee-sXXXX”, or visit “http://10.44.77.254” to configure the extender.

Note: Connect a modem for uninterrupted connection via the 100Mbps Ethernet port.

LED Descriptions

System Status LED

router.
Blinking| The device to access the Wi-Fi network of the primary router.
Red| Solid on| The network is unreachable.

Signal Status LED

2. Connection failed.

Access Extender Settings

1. Via Reyes App: Download the Reyes Router App to get advanced features, such as turning off the LED, and setting the Wi-Fi name and password…
2. Via Web Browser: Visit http://10.44.77.254 to view or change extender settings.

Troubleshooting

1. Locate the extender properly
   If only one signal bar lights up after setting up, plug the extender closer to your router.
   Plug the extender halfway between your router and Wi-Fi dead zone (within router signal range).

2.  Reset the extender
   Press the Reyes Mesh button for more than 5 seconds. If the is blinking, the device is restoring factory settings.
   Wait for 1 to 2 minutes. When the turns solid on, the device has restored factory settings.
   Repeat the configuration after the device reboots. The default SSID is @Reyee- sXXXX.

3.  Management Password
   You are advised to enter the Wi-Fi password. If the password is still incorrect, please restore the device to factory settings (Press the Reyes Mesh button for 5 seconds).

Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2.  this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Statement:
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules.

RF Exposure Warning!
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IMPORTANT!
Operation in the band 5150-5250 MHz is only for indoor use.

Innovation, Science and Economic Development Canada Statement
This device complies with Industry Canada’s license-exempt RSS.
Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Exposure Statement：
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS‐102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
RF Exposure Warning!
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

5G UNII-1 Statement：

1. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
2.  DFS (Dynamic Frequency Selection) products that operate in the bands 5250-5350 MHz, 5470-5600MHz, 5650-5725MHz and 5745-5825MHz.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>